Recommended Posts

Posted

How's everyone doing? I have been in the hobby for 8 months now and love it. Wood Talk Online Radio and the hosts' respective web pages have been great guides along the way.

I am about to purchase a lathe and I am looking for some direction on what I need for turning pens, bowls, spindles, and such. I am trying to decide between the Grizzly G0658, the Jet JWL-1220, or a cheap HF model. I prefer quality since I only want to purchase one lathe over the next 2 decades. Any suggestions?

Posted

How's everyone doing? I have been in the hobby for 8 months now and love it. Wood Talk Online Radio and the hosts' respective web pages have been great guides along the way.

I am about to purchase a lathe and I am looking for some direction on what I need for turning pens, bowls, spindles, and such. I am trying to decide between the Grizzly G0658, the Jet JWL-1220, or a cheap HF model. I prefer quality since I only want to purchase one lathe over the next 2 decades. Any suggestions?

Okay, lathes...I know.

I started with the Jet 12-20. It's a great starter lathe; but like any small lathe--it's just not going to do all aspects of turning. First, there's the real need for variable speed rather than changing belts. (I'm on my third,AND FINAL, lathe and it's got EVS--only way to go!!!) Second, the smaller lathes do wonderful spindle turning projects (pens, chisel handles, short spindles, etc.; but, they're terribly lacking when loading a green split log that needs rough turning. Smaller lathes have inadequate weight to counter the racking/rocking/bouncing; and, they're just not designed to handle the heavy-duty pounding of big, rough turning. Now, there are some exceptions--think, Vicmark or General small lathes--at much higher entry prices. As to price, my first chuck cost nearly the price of the lathe new!!!! And, the better turning tools cost usually over $70 a pop. (BTW, I started with the red HF set and still use some of the them, but bowl gouges (think pricey) are my favorites.

What should you buy? Dunno! But, check out the local wood turning clubs in your area and visit some members. These guys either have sunk major bucks in the best, or they really know the best bang of the smaller buck investments. If you fare as I did, you might pick up a bigger, better lathe at a lower fraction of new--now that's fun.

Turning is lots of fun, is very rewarding, expensive, and can be quite dangerous. Be glad to share more. Do check out the General lathe (about $700) because it may be the one small lathe that will do it all.

Arch

Posted

I've got the Delta 46-460. It's got variable speed, 12.5" swing, 16"+ between centers, direction reverse and a 1hp motor. I've yet to bog it down, and I find that I use the variable speed quite a lot. The reverse switch is nice for sanding the grain opposite direction from how you cut it. That said, if you're going to limit yourself to turning pens, it's overkill and has a higher buy in than a mini lathe.

But if you think you're going to turn bowls or platters up to 12" it's the best one of the bunch I found. Bonus, if you want to turn legs later on there's a bed extension available for the Delta that just bolts on to increase the capacity between centers. I was sold on it when I used the same model at Woodcraft for a beginner turning class. I ponied up the bucks for it, and I haven't regretted it. Given that you say you only want to buy one lathe, I think you'll want to start here. However if you want even more capacity, I hear the Nova lathes are good.

Posted

Actually that Delta 46-460 lathe is the one I have been coming back to. I don't really have a desire to turn bowls and plates larger than 12" for many reasons. One being my wife doesn't like unfinished wood...even if she knows the inside is not finished. I know its strange.

Does the variable speed switch easily? Looks like it is a lever the changes belt positions. How does that work for you?

Thanks.

Posted

There's three controls on the top. An off/on switch, a reverse motor direction switch and a knob that is twisted to set the speed within a given pulley range from 1 to 10. The RPM range is set by loosening the pulley tension with a lever inside a door on the side, you then slip the loose belt onto the next set of pulleys for the desired speed and tension it again. In practice I've had it set on the original set of pulley's for everything I've done and used the speed dimmer to set the speed. This arrangement works very well so far.

Posted

Good. I'll put it st the top of my list for now. I keep coming across small projects that are made on a lathe and I am getting more anxious about getting one in the next 12 months.

Posted

I'll tell you what I was told. Don't buy a lathe until you have all your current projects finished, otherwise they will languish on your bench while you make the world's most expensive dowel rods. B)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined