Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Round over the end of a hard wood dowel

Featured Replies

I'd like to round over the end of a 6' x 1.25" hard wood dowel.  I'm thinking of putting a roundover bit in my router table and setting the fence so that when the dowel is against the fence the bearing of the bit rests on the center of the dowel.  Maybe clamp a board to hold the dowel between the fence and the board.  Then feed the dowel into the spinning bit, then rotate the dowel.

Another approach would be to use the belt on my Rigid spindle / belt sander and free hand it.  I've heard of people using a hand drill to spin the dowel, but at 6' long that seems like a bad idea.

Is there a better way to do this?  

 

 

  • Popular Post

Last Christmas I built each of my granddaughters some sort of weaving thing. It was a 6' long board with 1" dowels, 4" long, sticking out of it every 2". To make the dowels, I did what you first suggested. I setup a stop block so that the center of the dowel was on the bearing. Fed the dowel in and rotated, then took to the miter saw and cut it off. Rinse and repeat. It was a lot easier and safer than anything else I could come up with.

Unless it had to be perfect, I'd probably rough it out with a rasp and then finish it on my Rigid belt/spindle sander.

At 6' long trying to feed the dowel into a router bit seems like a "if I lose focus for just a second thing..." 

  • Popular Post

I vote for a disc sander with a miter gauge clamped into position.

DiscSanderDowelRoundOver.thumb.JPG.daf4468c73ca61b783eb5258304d3f03.JPG
Set the main chamfer, then smooth the round over free hand.

  • Popular Post
On 7/16/2026 at 4:23 PM, Beechwood Chip said:

An inkle loom?

No, I had to look that up, but definitely not one of those. Honestly, I don't know anything about them. I just do what I'm told.

Here's a picture of the finished product. I had so many dowels and roundovers (60 total), I wasn't going to spend the time to do anything by hand.

image.thumb.jpeg.40e28720511caf49c5f7f61b48a1a27a.jpeg

  • Popular Post

Something like this clamped to the router table?

 

Router Table Dowel Rounder.jpg

I should have been more descriptive.  In my mind the block is clamped to the router table,  The roundover bit is buried in the fence or a sacrificial section of fence.  I do router table fence ZCI's like so.  Pretty crude but effective.  The ZCI makes a good perpendicular feed stop since it hugs the shape of the bit.

RouterFenceZCI-1.thumb.JPG.6fbafdf9bba0b73f8445286cbebb1797.JPG

RouterFenceZCI-2.thumb.JPG.23f0601878846966e635cc1a4c3dfc2d.JPG

The dowel would be inserted into the clamped block, walked up to the bit / fence while being rotated by hand.  The challenge is that a bearing guided bit will have no surface on which to bear at the final pass of the cut.  This is when the ZCI approach works out well.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.