Recommended Posts

Posted

So have have about $1,200 I'm able, or should I say allowed to spend on the shop!!!

Equipment I plan on buying over time, some things I consider a must still.

I need a jointer, a drum sander and a band saw. Three major items I'm missing.

I put the band saw at the back of the list, it is a need but doesn't do much in the pursuit of square boards.

With my festool mft, ts75 and 13" planer I am seeing better than average results.

So I'm down to a jointer an a drum sander. But I don't have enough money to buy the best of either.

And I can't forget about the festool domino and dust extractor...

So I guess the question is what would you do?!?

Thanks in advance.

This forum has a great wealth of knowledge and provides a great learning curve.

Posted

I'd ask what kind of projects you do the most. The type of project would dictate the tool.

Case work with a lot of flat panels and doors might benefit the most from the drum sander. If you like to use rough cut stock and mill your own then I"d go with a jointer, I think you should be able to find a good quality 6 inch one for that money.

For me and the type of projects I do I'd get the jointer then the band saw. I do a lot of smaller projects with curves and veneers. I have no consistent need for a drum sander.

Posted

Thanks for the feed back. I do all sorts of stuff from small boxes to dressers and furniture, well for that matter I really enjoy doing everything. I'm not a professional I just really love woodworking.

My only concern with jointer is I can't afford a really good 8" jointer and and I don't have 220/v out there. If I go in the shop a very small amount of the lber I have is under 6".

Over all I still feel like that is my biggest need at the moment.

Posted

I was looking at that, the only problem is with a 8" jointer I need 220v, to do that I would need to upgrade the entire service for the house.

Nah, just put a sub-panel in the shop. You'll thank yourself later. :)

Posted

Not the entire house to 220, I only have a 100 amp panel and have two dedicated 20 am circuits to the shop, i don't have the room in the panel to put another circuit out there.

If need to pull anymore to the shop I need to upgrade to a 200amp service.

Posted

I have 100A service, too. The only reason you'd need to upgrade to 200A service is if you're running a bunch of machines plus household appliances at the same time. You can run a sub-panel from the main panel to the shop and get the 220V you need fairly easily.

Posted

I have 100A service, too. The only reason you'd need to upgrade to 200A service is if you're running a bunch of machines plus household appliances at the same time. You can run a sub-panel from the main panel to the shop and get the 220V you need fairly easily.

Agreed. If you already have a double breaker in your main panel for the shop, replaced it and the wire with a higher rating, and put a sub panel in the shop.

Posted

I have 100A service, too. The only reason you'd need to upgrade to 200A service is if you're running a bunch of machines plus household appliances at the same time. You can run a sub-panel from the main panel to the shop and get the 220V you need fairly easily.

It's not a double breaker, it's two sepetate 20amp.

A thought, I have 220 on a 50 amp breaker, it's on a sub panel under my deck. It is for my hot tub, it only polls a lot of amperage when it's on. Could I run a 50amp sub to the garage off of that. Then I would have two 20 amp and a 50amp. Plenty of power.

Posted

It's not a double breaker, it's two sepetate 20amp.

A thought, I have 220 on a 50 amp breaker, it's on a sub panel under my deck. It is for my hot tub, it only polls a lot of amperage when it's on. Could I run a 50amp sub to the garage off of that. Then I would have two 20 amp and a 50amp. Plenty of power.

That's what I'd do! In fact I might run two 220 lines into the shop just in case you decide to get a bigger DC, that way you can run them on two different circuits.

That Griz is 220 only...I have that jointer. Good machine for the $.

Posted

if it was me i would get the jointer boards are never square, dust collector because that is a must for health, and drum sander you can get away with a belt sander untill you can get a drum sander. as for the power sorry i only have lower power tools.

Posted

Jack,

You said that you have 2 20 amp 110 volt circuits running into the shop. If that is the case you can get a lets say 50 amp 2 pole 220v breaker and remove the two 20amps breakers which will free up the two slots needed for the additional 50 amp and then run something like 6ga to a sub panel in your garage. You can then with in the sub panel put 2 20amp circuits and a 220v or two. just remember that all you have is the 50 amps so just think about how many amps your pulling at a time. I run a pro shop on less than ideal power...I have 60amps and that is enough for me to run my lights, 3hp 220v table saw, 5hp cyclone and an airconditioner if needed. if you are working alone you don't need that much amperage. Also keep in mind that anything that is 220 pulls half the amps as it would if it was 110. This would be the best way to go for the long run. hope this helps

Posted

Jack,

You said that you have 2 20 amp 110 volt circuits running into the shop. If that is the case you can get a lets say 50 amp 2 pole 220v breaker and remove the two 20amps breakers which will free up the two slots needed for the additional 50 amp and then run something like 6ga to a sub panel in your garage. You can then with in the sub panel put 2 20amp circuits and a 220v or two. just remember that all you have is the 50 amps so just think about how many amps your pulling at a time. I run a pro shop on less than ideal power...I have 60amps and that is enough for me to run my lights, 3hp 220v table saw, 5hp cyclone and an airconditioner if needed. if you are working alone you don't need that much amperage. Also keep in mind that anything that is 220 pulls half the amps as it would if it was 110. This would be the best way to go for the long run. hope this helps

Thanks!!!! It's really a good idea and seems like a pretty inexpensive one! Many thanks

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 54 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined