Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Drilling circular dog holes

Featured Replies

I am planning to add circular dog holes as i get on with the build and as all the drills i can get here are metric I am going to be stuck with 19mm, of which there is not a great choice.

What type of bit would you recommend for these deep holes? and any special points to note when doing this. I am hoping that I can get most, if not all done on the drill press.

CC

I've drilled holes in large items, including my own benches, using a shop made guide.

The guide is a 3/4" board with two holes spaced the distance you want the finished holes spaced.

- Glue a 2" thick hardwood block to one part of the board. Let dry

- Drill one hole through the 2" block and base using a drill press, or whatever way can get you the most plumb hole using the tools you have.

- Drill a second hole in the base, spaced as you want your dog holes.

- Place the block on the bench with the 2 3/4" thick hole where you want hole #1.

- Insert the drill bit / hand drill into the block. Drill as deep as you can.

- Remove the block and finish the hole

- Use a dog to locate the hole without the block in the hole you just drilled.

- Drill the second hole

- Repeat

Clamp a board to the bench for side of your guide to sit against. This will set up your straight line.

The guide will easily last through a bench project with no special treatment of the guide hole.

I really like Lee Valley's brad point bits that are reground from twist drills. They make CLEAN, perfect holes.

Glad you asked this question because I too was wondering what would be the best drill bit for these deep holes. As a newbie, I was thinking a forstner bit because of the nice clean holes they create but I worried that I would burn up the forstner bit long before I got all the holes I need drilled in the hard maple I am using for the top. My forstner bits aren't the greatest and I was thinking I just needed to buy better forstner bit but it sounds like brad point bits are the way to go.

Boring bits will work too. i bought a set from Rockler a few years back that is working quite well so far. generates less heat than a brad point bit too.

Marc, do you mean spade bits or auger bits?

(Maybe an amazon part number reference?)

I used a cheap forstner bit to drill about a million holes in my LVL and plywood bench. The bit worked great and made really clean holes. If the bit gets a little dull it's easy to touch it up with a file. You will want a drill press if using a forstner however. They will wander if used freehand.

Forstner

I used a cheap forstner bit to drill about a million holes in my LVL and plywood bench. The bit worked great and made really clean holes. If the bit gets a little dull it's easy to touch it up with a file. You will want a drill press if using a forstner however. They will wander if used freehand.

Huh? All the forstner bits I have seen have a center spur which would prevent them from wandering if used freehand, unless you try to start boring a hole at an angle.

Huh? All the forstner bits I have seen have a center spur which would prevent them from wandering if used freehand, unless you try to start boring a hole at an angle.

True Chris, the point stays in one spot. But it's easy to start tilting from 90 degrees, and because the shaft is thin compared to the "head" you can make a nice gentle curve if you're not careful. Think of a piece of elbow macaroni, but obviously not as exaggerated. Or yummy. For some purposes this method would be "straight enough" but if you're trying to put a round dog or a holdfast in there you'd go nuts.

A forestner bit is the worst choice for handheld drilling. They tend to go off course, particularly with long holes through hard wood. However, they are excellent in a press, and a single bit will easily do an entire bench.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.