Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

How to: plane a rough piece, when you don't have a benchtop planer

Featured Replies

I have very little budget for a bench top planer. I only have a jointer, because I saw one in the local classifieds which was about a fifth of the price new. I have yet to see a bench top planer come up. I do have a mitre saw, a table saw, and a router, and a powered hand plane.

Is there an easy way to get parallel sides without a bench top planer, at least until I can save up for one?

My jointer can only do 6" wide boards, so I was thinking I could joint three sides first so they are flat and square, and then use the table saw to finish the job by running it through to do 3", then turn it over to do the other 3". To do this I'd have to remove the safety guard - though obviously the knife can stay in situ.

I've not yet tried this - I'm speculating. Do you foresee any problems with doing it this way? Has anyone tried this and found it impossible for some reason?

You could joint the one face and then use your router with a sled to flatten to other face . There's a video in the guild that shows how , I"m sure you can find some vids on youtube too .

No point in jointing three sides. I'd skip the table saw trick and buy a decent handplane. You're gonna get a lot of burning doing that on the table saw and will end up having to plane the burn off anyway. And I consider that operation pretty dangerous, too. I've done it, but I don't like it one bit.

Reality check: Put ten bucks a week in a jar and you'll have your lunchbox planer in less than a year. :)

How much wood does your hand held powered planer take off at a pass? If you can dial it down so that it can take off 1/64" or so of wood, you can use that in place of a hand plane for thicknessing purposes.

You dont need any funky jigs. Face joint your wood, Edge joint, rip to width (make sure blade is 90). Lay the piece on your jointer or saw table and get rough idea of how bowed it is. Now cut two strips of scrap any wood. 1/4" wide x 3/16 thick. Run your work piece through your saw on edge keeping it tight against the fence (featherboad if needed) with the blade raised 1/4". All you are doing is creating is creating a rabbet on both long edges. The rabbets will be parallel if you keep the wood tight to the fence. Now tack glue the strips into the rabbets with super glue. A tiny drop every 8" is plenty. Now face joint the board with the strips against the jointer. The strips are already flat and parallel to the other side. Keep making passes untill the strips are gone. Obviously you will need to adjust the strip and rabbet dimensions as needed. Think about what your doing ahead of time and face the bow the right direction, use good jointer technique. There are other mothods that use a dado blade if you prefer.

Don

  • Author

How much wood does your hand held powered planer take off at a pass? If you can dial it down so that it can take off 1/64" or so of wood, you can use that in place of a hand plane for thicknessing purposes.

It's a European tool - so it's in mm not inches. It *says* it can go down to 1/4mm (and 0mm too). I don't know how accurate that is though, never measured it. The sole isn't huge - about 9 1/4" long, by about 3".

  • Author

Don - I might give this a try and see how I get on with it. If nothing else it would be an experiment, and good practise with some unfamiliar tools.

I don't currently have a Dado blade set - it's on my (rather long) Christmas list! Unfortunately, I suspect I'll need to replace my table saw - it was very cheap, and it doesn't look like there's much space on the arbor for blades much wider than a standard blade :(

It's a European tool - so it's in mm not inches. It *says* it can go down to 1/4mm (and 0mm too). I don't know how accurate that is though, never measured it. The sole isn't huge - about 9 1/4" long, by about 3".

If you can get it down in the range of 1/4mm, that should be good enough. That's taking shavings of less than 1/100 of an inch, which is probably less than most planers can do. As franklin pug said, face joint your board with your jointer, watch Bob Rozaieski's video, and try your hand held powered planer instead of a hand plane for thicknessing the board, which is in the second half of the video.

  • Author

It's useful to have several different methods to achieve the same goal, so I'll try both the plane and saw/jointer method. I don't have a huge amount of time right now to build a router sled so that method will have to wait.

Thanks for the link to Bob's video - very informative. Lots of other info on there too - thanks!

Andrew, I know this is a late reply but the use of a router sled after jointing one side is an excellent one. If you were a member of the Guild you can watch the video where Marc builds a quick and dirty router sled to level his Roubo workbench. The sled could be your goto for thickness planning until you have a planer and can be used for jointing on stock bigger than your jointer. You will need a large diameter bit and take multiple passes if you are removing a lot of material. And you might want to leave 1/32" for final pass with a hand plane.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.