jefe Posted April 13, 2012 Report Posted April 13, 2012 I'm just getting into woodworking, and while I slowly create a work area, I also get the privilege of cleaning/repairing some of my grandfather's tools, that were not maintained after he died. I know a decent amount about sharpening, but I am lost on rust removal, planer blade setting and a few other issues, I'll list the tools I've found as accurately as I can and their issues, and maybe someone will know how to help me out! I can post pics of any that need them Spokeshave and curved spokeshave - how to set the blade, what do I reference on the curved one to set it, pretty clear of rust compared to others Japanese pull saws - all seem in good condition but have rust spots, I usually grind rust off with sandpaper, but these feel really thin to be rouging streaks out. 4" jointer - no company branded anywhere, AMT motor was next to it both with v-belt pullies, moves, adjusts, has a strange fence on it that doesnt set right, and no clue how to set the blades, the locking threads are in an awkward place, I have a pic of the cutterhead ill send up, since the pic Ive cleaned the blades, in the process of buying new Lathe encrusted with rust - havent started on it so I dont know its condition, was hoping someone might know a rust removal trick Quote
Jonathryn Posted April 13, 2012 Report Posted April 13, 2012 Spokeshave and curved spokeshave - how to set the blade, what do I reference on the curved one to set it, pretty clear of rust compared to others Setting blades on spokeshaves is usually trial and error. A good starting point is to put a business card or a piece of paper folded over on either side of the mouth opening, lay it flat on a wooden surface (so you don't dull the cutter), and project the blade through the opening so the cutter is "proud" of the mouth opening created by the depth of the paper. Then lock it down with the screw and give it a try. Japanese pull saws - all seem in good condition but have rust spots, I usually grind rust off with sandpaper, but these feel really thin to be rouging streaks out. Mineral spirits and 220 grit or finer sand paper on an appropriately shaped- and sized sanding block. 4" jointer - no company branded anywhere, AMT motor was next to it both with v-belt pullies, moves, adjusts, has a strange fence on it that doesnt set right, and no clue how to set the blades, the locking threads are in an awkward place, I have a pic of the cutterhead ill send up, since the pic Ive cleaned the blades, in the process of buying new They look all right. Before you buy new ones, sharpen them up and get the rust off with mineral spirits and a steel bristle brush. There's a video on how to set them here. Lathe encrusted with rust - havent started on it so I dont know its condition, was hoping someone might know a rust removal trick. Nylon bristle brush and mineral spirits on the painted surfaces, steel bristle brush and mineral spirits on the exposed metal surfaces. After that if there are rusty bits, put them in ordinary vinegar for 2-4 hours, wash them, and go over them with the steel bristle brush and mineral spirits again before it flash rusts. Then put some 3-in-1 oil or paste wax on them to keep the rust off. Lathes and other stuff get so clogged up with sawdust that it doesn't make sense to me to go whole hog and put new paint on, but others may disagree. Your call. Quote
jefe Posted April 15, 2012 Author Report Posted April 15, 2012 Thank you so much! I can't wait to get going on these, unfortunately some masters research papers are drawing closer to due... Quote
Jodavis Posted April 22, 2012 Report Posted April 22, 2012 For the hand tools I recommend electrolysis. As for the lathe the previous comment is good Quote
Andrew Pritchard Posted April 28, 2012 Report Posted April 28, 2012 Someone recommended using white vinegar to help remove the rust - what do you guys think? Quote
theapprenticeshand Posted April 28, 2012 Report Posted April 28, 2012 Someone recommended using white vinegar to help remove the rust - what do you guys think? I'm not sure how well vinegar would be all on its own. It may work, but may be real slow. If you have a harbor freight nearby, evaporust is good stuff and works relatively quickly. It just depends on the surface from which you are trying to remove rust. Razor blades and sandpaper combined with a strong acid work well on surfaces like jointer beds and tablesaw tables. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.