Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Removing a stain/fade mark?

Featured Replies

I have recently stripped down an old night stand that was finished with what appeared to be a tinted shellac. This is part of a bedroom set that was handed down to me from my great aunt. Best I can tell, the furniture was bought in the 50s or 60s. I have used it for years, but I did a number to the top with a water glass.

The water stain sanded out, but the areas behind the drawer pulls are a different shade than the rest of the stripped wood. The drawer fronts have been sanded to 220 (60 - 100 - 150 - 220) and yet the faded areas remain. I don't want to have to be forced in to using the old hardware, but I am not sure how to get rid of the fade.

Any suggestions are greatly appreciated.

Thanks in advance.

Jim

post-6823-0-00310700-1341887657_thumb.jp

Well, just leave the hardware off for awhile. That looks like Cherry so it'll darken with UV exposure; it wasn't getting much under the hardware. If you have a sunny window in the house, put it in the sunshine to help it out. Just be careful about putting it out in the sun outdoors since those surfaces might become much warmer and drier than the other surfaces and cup.

Some woods (cherry, famously) are like bikini models in that they darken with exposure to light. So on your drawers, the problem is probably not that the areas hidden by the hardware have faded, but that all the exposed areas have darkened. In short, your drawers have tan lines. That sounds a little odd because tan lines are usually caused by one's drawers, but there you have it.

So what to do? Remove the hardware from the drawers and put them in the sun au naturel for a while and see if the places that were covered by the handles tend to darken to match the uncovered areas. If they do, then you can bet that over time the colors will eventually even out on their own, and further that they will even out faster if you intentionally expose them to sunlight.

If the sunbath treatment doesn't produce the expected results, or if you are in a huge hurry, then you could always punt by making sure that whatever new hardware you get completely hides the places where the old hardware was. That would be somewhat analagous to putting an overcoat on a bikini model, and about equally advisable.

-- Russ

  • Author

Thanks guys. I'll put them in the sun for a bit, sans spf. Should I cover the areas that are already tan?

Should I cover the areas that are already tan?

I don't think you need to do that. If they're 50 or 60 years old like you say, then they're probably already as dark as they're going to get.

-- Russ

I bet that the effort to tape off the areas except where the hardware was would help speed the darkening to match. I had a board which was 1/2 covered and the sun darkened the exposed section. I just covered the dark section and kept an eye on it until the color was even.

Just my opinion... Your results may vary < grin>

Should I expect this to take days? weeks? more?

Depends on the wood, I suppose. If it's cherry, you will see a color change pretty quickly ... hours or days, I would guess, in direct sunlight. I'm not sure about other woods, or how long you'd need to wait for the colors to completely even out.

-- Russ

  • 3 weeks later...
  • Author

Thanks for everyon'e replies and recommendations. Leaving it in the sun for a couple of days didn't produce any noticable change and I didn't want to stain it due to the great figure in much of the grain. So, the end table is in the process of gettng sealed up and moved off my bench. I'll just end up using the same old hardware.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.