Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

I don't know if this has been posted, but...

Featured Replies

I know it is a woodworking question. This is a little different, and you are just the people to ask.

I have followed The Wood Whisperer since before the "Hot and Fresh Woodworking" days and this community is great!

In addition to light woodworking, I've built a basic rolling desk, I am an avid older car enthusiast. That being said, I have a 1984 Mercedes Benz and it has quite a bit of wood for the center console and other trim in the dash. As with all wood and finishes the appearance has faded with time and cracked on the lower console and I would like to repair it.

Here is the catch: It looks to be a paper thin laminate and the finish has a tint or color. As a new woodworker, I don't even know where to start! :unsure: It looks like plywood and the laminate is so thin it looks like you would sand through it without applying pressure. As far as matching the color of the finish, I will need all the help you can give.

The pictures that I have included are of the top console (full pic and side pic), the chip out of the center console that shows wood color and the color of the finish from the chip that came off. I hope this helps.

You won't offend my by making your explanations simple, and any help you could give would be HIGHLY appreciated and I look forward to your responses.

Thanks

Todd

post-7192-0-45093500-1341967241_thumb.jp

post-7192-0-62680800-1341967251_thumb.jp

post-7192-0-34302200-1341967261_thumb.jp

post-7192-0-35803600-1341967281_thumb.jp

The standard answer when it comes to finishing and color matching and all that is, "Practice on scraps." That's great advice when you're working on a new project and have some actual scraps of the wood you're dealing with. You have a problem, though, because you don't have any scraps. Also, you quite understandably don't want to make the situation worse than it already is by sanding through that thin veneer.

A couple of questions:

  1. Is that part a curvy thing, or does it look like it was just cut out of a flat sheet of plywood?
  2. Are you only worried about that one part, or do you want to refurbish all the wood in the car?

Depending on the answers to those questions, you might want to consider starting from scratch and reproducing the part with new material, rather than trying to repair the old part. That approach would eliminate the risk of further damage to the original part, and would give you the opportunity to experiment with various finishes and techniques as many times as you need to get it right. Also, if you decided to replace all the wood in the car, your worries about color matching would basically go away.

-- Russ

  • Author

Russ,

Veneer! I knew I was using the wrong term! :rolleyes:

Thank you for the reply. Though it looks curvy it is actually suppose to be straight as it attaches to an aluminium plate backing, and yes it is one single piece of plywood as I think each piece is. As much as I would like to replace it all there is quite a bit of wood and some of it bends to a 90 degree angle around the dash. The center console chip is right by a hole that is milled to fit a hazard (pic 2) switch and that would be very hard to replicate + the part that faces the back bends to almost a 90 degree angle. See pics.

I would like to refinish the one console (pic 1 and 2) at this time and that first piece is fine, I just used it to show you how it is made. I may be able to find a scrap yard with an old car and pull some trim off to practice on. And, I agree that the colormatch will be the toughest part as it will sit next to an older piece. This car is not a collectable so really close is good, I am not holding my breath over a perfect match.

Sorry about the picture quality, I don't have the best phone!

I have seen other peoples attempts at this and it just doesn't look good, not that the alternative is better, but if anybody can help me pull it off it's you guys!

Paul,

Though I think you are correct, it may be a little out of my realm of expertise to take on that project! :D

post-7192-0-74628000-1342017296_thumb.jp

post-7192-0-85465400-1342017309_thumb.jp

post-7192-0-27781200-1342017315_thumb.jp

post-7192-0-93994600-1342017322_thumb.jp

post-7192-0-51415100-1342017447_thumb.jp

  • 1 month later...

Wow. Thats toughie. I honestly can not dish out advice here but i am intrigued to see how you do. Rooting for ya. Good luck!

Todd, if you go to the Mercedes dealer they can tell you what the original veneer and finish was on the console. However, you will have to play with the finish in order to try to reproduce a matching color, due to age and the effects of sunlight. You may be able to simply reveneer the piece that is damaged and then reinstall the switches.

Sometimes it is better to just go with a contrasting wood as an accent, rather than try to match the rest and not get it exactly right. Maybe put a red (cherry?) stripe across those three switches, and maybe put a stripe of the same color and width above the ventilation controls. I got the idea from

==> just go with a contrasting wood as an accent

+1...

You will drive yourself crazy trying to match existing unless you are willing to remake entirely. I know some specialist refinishers in NYC who can match anything and specialize in museum-quality furniture restoration, but they would charge more then the car is worth.

  • 2 weeks later...
  • Author

I knew I came to the right place for this question! Thanks for the input, all great ideas. I'll see what I can do and hopefully, if it isn't too far off, post some finished pictures.

hhh, yes it would cost more than the car! :D

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.