Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing boxes

Featured Replies

I'm working on a keepsake box...oh, say 8x10,4. What kind of finish do folks recommend for this application?

I was initially going to use the first two buffs on the Bealle system (before glue up on the interior pieces), assemble, some kind of penetrating oil, and then a couple of coats of a water based wipe on poly for durability. I feel that polishing on bare wood has a unique look to it, but maybe it doesn't and I'm nuts.

After thinking about this, I've run myself into a circle as to the validity and value of this recipe.

Can I get a couple of opinions on other folks like to do and/or a thought process on my recipe (for disaster)?

Any kind of sanity check would really help.

Thanks

scott

I use a wiping varnish on all my pieces sanding in between each coat with successive grits to about 600 and then finish with a couple coats of wax that are then buffed with 00 steel wool and then 0000 as the final. Gives a smooth as satin finish that's easy to repair if ever needed (but honestly I've yet to ever have to repair one)

  • Author

A wiping varnish could be a wile on poly?

I have never buffed w/ steel wool...only as a "scratch coat" between applications of finish. Do you just hit it with the steel wool with a real light touch?

I like to build up my finish (once sealed) with 3-5 coats, sanding with 320 in between each. Then rub with oooo steel wool. You want more than just a light touch. Give it enough pressure to see the sheen change. Make sure to go with the grain, just like sanding. Watch the sheen in the light and make sure it is rubbed down nice and even all over. Next rub it with a clean cloth or bath towel, good pressure. This will bring back some of the sheen. If you want more gloss back, wax it with furniture wax.

Try it out on a test board.

I'd like to know how it goes for ya.

I'd spray the box with nitrocellulose lacquer and rub it out.

Spray bombs (cans) would work fine, but you need many more coats than a gun. Build coats slowly, sanding is not needed between coats, rub out the second to last and last coats.

If you use steel wool during rub out, don't forget to orient the wool fibers ACROSS the direction of rubbing.

I don't take it easy on the steel wool. I do however start the finishing process after sanding to 150 grit, from there moving to successive coats of finish with a sadning of finer and finer grit inbetween. Once I get to the steel wool I'm at least 3 coats of wiping varnish in. I'm also a fan of the apply a tad heavy, let sit/soak for a few minutes and then wipe dry process. Once I get to that 3rd coat or so the medium grade steel wool is pretty much doing nothing more than burnishing the surface. I'm sure if I really wanted to get into it I could remove material, but I honestly don't give it much thought and I don't pay that much attention so I would say it's safe to say that I'm not going at it with kid gloves. Ultimately each coat sits a minimum of 24 hours before moving to the next grit & application of finish. Typically I'm adding 3-4 coats of wiping varnish and 2-3 applications of wax.

This isn't going to give you that wet shine/polished look, but will give you a piece that is a dream to touch.

I have used water based finishes for many years . Skip the steel wool and use those plastic abrasive pads. Use thin coats of finish, it dries quicker and less drips and runs to clean up.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.