Andrew Pritchard Posted July 26, 2012 Report Posted July 26, 2012 I have been looking for a second hand TS for a little while, but none of the ones that have come up on Kijiji have been suitable until now. My current saw is ok-ish, but the top is cast aluminum and rather small (maximum width 24" on the right, 12" on the left). I've noticed that the fence isn't very accurate and I keep on having to double check that the front and back are the same distance from the blade. I'm also a little paranoid about the switch - it's a bit low down for me to reach in an emergency. Finally because it's a cheap saw, and gear driven it's very very noisy. My hearing isn't great as it is, and even wearing ear defenders it still sounds very loud. So when I saw a Ridgid TS3650 come up, I was interested. The photos do show that the current cast iron top hasn't been very well looked after - it's brown with rust and dirt (not a major problem I've got an RO sander!). I also noticed that the blade guard isn't in the photos, and the current owners can't find it at first glance. They want $300 CDN for it. That seems like a reasonable price, but I'm very concerned about the missing blade guard - if it's lost it's a no go as there's no other riving knife, or splitter system. I've done a little hunting around to see if I can find a replacement, but it's already 4 years old and a couple of sites say they don't supply them any more. I guess my question is - oh internetz - is this a good deal? 1 Quote
rodger. Posted July 26, 2012 Report Posted July 26, 2012 I have a TS 3650, and I love it. I have had it for 8 years, and it has never let me down. I have cross cut and ripped tonnes of lumber, mostly 4/4 and 8/4. 300 dollars is a reasonable asking price, if the saw is in clean, in good working order with all the parts. I would haggle if the blade guard is missing (and tell them how expensive after-market guards are), and also ask about the manual. Make sure the mitre guage is in good shape, and also make sure the rip fence is not damaged. I use the blade guard on mine, and sometimes I use the incra micro splitter (yellow version) instead. Quote
Andrew Pritchard Posted July 26, 2012 Author Report Posted July 26, 2012 I found the manual on Ridgid's website, so I'm less concerned about that. There's also a parts list on the same site. The missing blade guard is my biggest concern. I've found a couple of sites that do replacement parts, but they both say that the blade guard is obsolete. That's a little concerning. I've only got a Lee Valley in at reasonable distance to me, although there maybe another less visible company in Halifax who can supply a replacement guard. A good point about the mitre gauge, I'd forgotten about that! Of course, if they've lost that, a new one of them is going to be at least $75 + tax. What's the rip fence like? Quote
Andrew Pritchard Posted July 26, 2012 Author Report Posted July 26, 2012 I tell a lie - there's a Busy Bee a little further from me, but not an unreasonable distance Quote
rodger. Posted July 26, 2012 Report Posted July 26, 2012 What's the rip fence like? The rip fence is excellent. I am very happy with it. The fence is solid, easy to move, and very accurate. It also has T-slots for jigs. They claim that is has a micro-adjust, but ignore that. It is not very good at microadjusting. Tapping it with your hand works better. I would still ask for the manual, as it gives you more leverage to haggle (wether you need it or not). How rusty is the top? Quote
knotscott Posted July 26, 2012 Report Posted July 26, 2012 You're likely to find that the guard system from some of the older Ridgid, or possibly even Craftsman saws will fit that saw.....they're all closely related. Also, the Craftex CT-146 is the same as the TS3650, so the blade guard should be a direct fit unless they changed it. You could also add a Microjig splitter...it's fairly inexpensive. Sharkguard also makes an aftermarket splitter for it.....more $. Either way, I'd offer $250-$275, but wouldn't let the lack of the guard be a reason to let the saw go, though it's definitely something you should have if you feel strongly about it. Quote
Andrew Pritchard Posted July 26, 2012 Author Report Posted July 26, 2012 Having had one incident which nearly resulted in a serious kickback, which injured me in another way (a long story, best told another time. Preferably when I'm a little less embarrassed about it! Just glad I live in Canada with our universal healthcare system), I've been using my splitter religiously, and the guard at every available opportunity. Here's a photo the current owners sent me of the top. I'm going to see the saw tomorrow morning. Quote
rodger. Posted July 27, 2012 Report Posted July 27, 2012 You picture didn't post. Maybe try again. Quote
Andrew Pritchard Posted July 27, 2012 Author Report Posted July 27, 2012 Grr - it was there yesterday! In three hours, I guess I'll know if I want to buy it! Quote
knotscott Posted July 27, 2012 Report Posted July 27, 2012 Looks to be in reasonable shape under all the crap. It should clean up nicely. It amazes me that people put things up for sale withouth doing so much as wiping the dust off. Making something shiny is an easy way generate interest...to me, the crud and rust make it a harder sell, and is valid reason to offer less $. Quote
Andrew Pritchard Posted July 27, 2012 Author Report Posted July 27, 2012 I know exactly what you mean knottscott. Thing is, he has said he'll clean it up for me. And it is *considerably* quieter than my other saw The rip fence is solid, and it's nice to see and big expanse of cast iron like that, even if it's a bit of a state right now. The bladeguard is AWOL, but he will drop the price by as much as the replacement guard. BusyBee's say they won't get one until the end of September! I'd like to be able to use it before then. I could use it without, but I'm a lot more cautious these days. Ridgid's guards are now obsolete - can't even find it on their own site. The Gardner Inc website say they'll ship one to me - $63 for the guard and $59.99 for shipping! Anyone know where I can get one without getting charged the earth for shipping? Quote
Andrew Pritchard Posted July 27, 2012 Author Report Posted July 27, 2012 ok - these guys are slightly less damaging. $74 for the guard, but only $23 for the shipping. https://www.mastertoolrepair.com Quote
knotscott Posted July 27, 2012 Report Posted July 27, 2012 Here are some pics of an older Craftsman contractor saw blade guard: Here are some pics of Ridgid contractor blade guards: Quote
Andrew Pritchard Posted July 28, 2012 Author Report Posted July 28, 2012 Hmm - they look remarkably similar too. Trouble is, I don't want to order something only to find it doesn't fit properly. Do know know what model of Craftsman? Quote
rodger. Posted July 28, 2012 Report Posted July 28, 2012 So you must have bought the saw. It is in pretty nice shape, and will clean up very well! Post a pic when you are all set up. If you need to wait for the blade guard, go to Lee Valley and get your self a micro-splitter. Then are fantastic. Quote
Andrew Pritchard Posted July 28, 2012 Author Report Posted July 28, 2012 Yes, I've decided to buy the saw. Now to persuade my folks to give me the money for my up coming birthday and Christmas From what I've seen of the micro splitters they're a good idea to have anyway. Quote
knotscott Posted July 28, 2012 Report Posted July 28, 2012 Hmm - they look remarkably similar too. Trouble is, I don't want to order something only to find it doesn't fit properly. Do know know what model of Craftsman? It's actually several. Most of the full size belt drive contractor saw models 113.###### and 315.###### should fit. If it has those prefix numbers followed by 6 digits, and looks like the 3650 splitter, the odds are heavily in your favor. The exceptions are smaller saws, direct drive, much older, etc. 1 Quote
Andrew Pritchard Posted August 1, 2012 Author Report Posted August 1, 2012 So I took possession of the new saw this morning. The top was still a state, even though the guy said he'd clean it up. Doesn't matter - that's what RO sanders are for! I also managed to bargain him down by the cost of the blade guard. I've already spent the better part of an hour cleaning it with an old 80 grit taking the crap off. Next stop a new 80 grit and then work my way up to a 220. Quote
knotscott Posted August 2, 2012 Report Posted August 2, 2012 Congrats on the acquisition. Regarding which splitters fit, I found this on the Sharkguard website...the same splitter fits all these models: Ridgid 3650, 2424, 3612 and some Craftsman models to include the 113.298150 ,298151, 298240, 298470, 298720, 298721C, 298722, 298751, 298761, 298762, 298842, 298843, 298844, 299040, 299315, 299510. Quote
Andrew Pritchard Posted August 2, 2012 Author Report Posted August 2, 2012 Well a few hours of working away with the RO sander and I've got it looking pretty good. It's allowed me to get to know the saw a bit better and I've spotted a couple of issues that I can easily resolve. The wings aren't level with the main table. The bolts holding it on look rather rusty, but they unscrewed on the left hand wing without difficulty. I've not looked at the right wing yet - not had time. You'll see from the photo the insert plate isn't flush with the table either. Some of the orange paint has been scraped off on the left hand side. That shouldn't be difficult to remedy once I've got an Allen key the right size! Not sure yet how I'm going to get the rust out of the mitre slots, but right now I'm not so bothered about that Overall, very pleased. Still needs a lot of love before it's usable. I'm going to make a zero clearance insert and add a splitter at the same time, something like this: Quote
robjeffking Posted August 2, 2012 Report Posted August 2, 2012 I have this blade gaurd off a ryobi bt 3000 will it work? Quote
Andrew Pritchard Posted August 2, 2012 Author Report Posted August 2, 2012 I'd be surprised if it would fit. There is a support mechanism, which wraps around the back of the table which means you can take the blade guard off with relative easy. Should be one thumb screw and you can slide the guard off. Thanks for the thought though Quote
Alan Bienlein Posted August 3, 2012 Report Posted August 3, 2012 I have a guard assembly from my Ridgid TS3650 you're more than welcome to. Just need to find out about shipping as you don't list a location. As for the rust in the miter slots get some red scotch bright pads and spray some wd40 in the slot and rub with the red scotch brite pad. Quote
Andrew Pritchard Posted August 4, 2012 Author Report Posted August 4, 2012 Thanks Alan - I've sent you a message Quote
Alan Bienlein Posted August 4, 2012 Report Posted August 4, 2012 Here are a couple pictures to make sure everything you need is there. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.