Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Help Spraying Zar Aqua Poly

Featured Replies

Hey guys,

I just picked up a Graco 2900 HVLP Spraystation. This has been a life changing experience! I have put off HVLP due to price and it was also intimidating. If I had known that $130.00 tool could transform my finishing I would have done this a long time Ago. The amazing results I am getting with a cheap sprayer, I can only imagine what a high end one can do.

Here is my question, I am spraying Zar Aqua water based poly on birch panels for kitchen cabinets. I have sprayed 3 coats, all are light and drying fast. Do I need to use more coats when spraying or should I try to put them on thicker? I am using gloss and would like a high gloss finish.

I am sanding between coats and happy so far, just curious if water will finish like oil?

Thanks,

David

My experience with water based finishes is that they require many more coats to get a comparable film thickness to an oil. I've been able to get the grains filled for a very smooth surface but have yet to actually build the depth that I'll get with a traditional spar varnish. Sounds like you're doing everything right :). Thicker films don't typically work too well (they can wrinkle, stay tacky / soft longer and also an increased chance of sags or runs).

The higher the gloss the more "woopsies" they will show so patience is the key. Unless there are blemishes to remove I would only be prepping the surface with a scotch bright pad or 320 grit. Because the films lay down pretty thin even minor scratches can show through the next coat making it appear a little duller..

  • Author

Thanks for the help, I will keep layering the thin coats. It dries in 30 to 45 minutes so its going quick. What should I use to "rub out" the final coat? Is it the same as oil?

IMO it's very difficult to rub out a high gloss finish as doing so will dull it's appearance :( I think what will give you the best result is to do your final coat in as clean of an environment as possible and hope the finish skins over before the dust finds it. More often times than not I'll actually wet down the floor so I don't kick up any dust while moving or walking around.

If you really wanted to shoot for perfection you could let the final coat cure for a few days (a full week or more would be better), wetsand the topcoat with 2500 - 3000 grit sandpaper and buff it out with an orbital buffer on very slow speed with a soft foam pad and a finishing compound. You'll need to look in a good auto store for the compound.

Two that I've used with very good results:

Wizards swirl free finishing compound (I believe this is a water based product that does not contain any silica or petrolium additives)

Finess-it II (this probably works the best BUT is expensive, contains both silica and petrolium).

My recommendation would be for Wizzards. You'll need to go over the surfaces 4-5 times but it will buff to a very high gloss :)

Good luck!

~Andy

AquaBuff 2000 may be another good option to try..

Edited by Boatworks Today

Have you seen this?

Lots of water based spray info is product specific.

For example, some products work well with thin coats, others don't. For example, I've been spraying ML Campbell Ultrastar since 2005. This product requires full, wet coats, but reaches a serious build in 2-3 coats. Others like to be applied as a greater number of lighter coats.

I've found that a wet mil gauge is very helpful with water based finishes. Ask at your local paint store, they often give them away. If your product does not specify a wet thickness, measure and note the thickness when you get great results. This makes it very easy to nail the coating every time.

With water based finishes, or even oil-based crosslinking finishes, like oil based polyurethane, it gets more important to nail the thickness the first time, as removing or repairing screw-ups is far more difficult than evaporative finishes like solvent lacquer and shellac.

If you can stand a little "ambering" in your water based finishes, spray on a seal coat of dewaxed shellac. This will greatly reduce any raised grain from the water base. Zinnser Seal Coat is an easily found, premixed dewaxed shellac. Don't use standard orange or clear shellac, as the wax in it will damage the water based finish's ability to bond to the surface. Don't do this on woods where you want a super-white look, as the shellac warms the color.

I have sprayed Hvlp and water base finishes for many years. Especially if the piece is stained I put 3 light coats on before I sand, and then be very careful of edges and corners to prevent sanding thru the stain. Then put on a wet coat, don't put so much it starts to look milky. You get a much better finish from a fully wet coat than cautious thin coats. You have to develop skills in avoiding overlapping and causing sags and runs . If you are going to try buffing out a water Bourne finish make sample panels while you are finishing the piece, do every thing to the samples you do to the project. Then practice buffing on the sample first. Let it dry at least a week before buffing.

  • Author

Thanks for all the great info, the project is going much better and faster then I expected. Each coat has added another level of gloss, I am on the 5th coat. At what point does it reach maximum gloss levels? I think it is protected but I can still see some pores showing through. Should it be a straight "sheet" of poly or am I good now? I am also going to pick up a mil gauge, that should help.

How do I interpret the Aqua Zar Spray instructions. It talks about Graco guns, no dilution for some and 5% for others but it does not say why.

  • Author

I did get a little heavy at times, and the finish sagged and ran. I brushed them out with a wet brush sanded and resprayed. Is there a better way to repair sags?

How do I interpret the Aqua Zar Spray instructions. It talks about Graco guns, no dilution for some and 5% for others but it does not say why.

It may be related to tip size or the number of stages on a turbine driven HVLP. Larger tips and more HVLP stages allow a higher viscosity product to be sprayed.

The 5% dilution...is typically spoken, that you "can" thin the product...but only up to 5% depending on your equipment, should you need to thin.

Remember, thinning a product reduces the amount of "stick" you have on vertical surfaces. Hence the product may run easier on you. Also, thinning a water based with water can shift the sheen some.

Food for thought...instead of buying a better sprayer and spraying cheap stuff, why not buy a better water-based product and spray with a cheaper sprayer. The reason a finish is cheaper, is due to "less" goodies contained in the finish. The spray gun/rag/brush/paint roller... gets the finish onto the wood. Then its the finishes job to lay on the wood and flow out really nice. Less goodies means less stuff on the surface to flow out.

The trick to spraying vertical surfaces is just wet enough before it run's. Someone new to spraying has to learn good technique and a raking light is very important shooting vertical, as well as, horizontal. You will be a dry sprayer till you become more confident with the spray equipment. It takes time behind the spray gun to spray "wet" coats.

Fixing water-based runs... if you can catch them in time? Brush them out the best you can and hit that area again with a spray gun. You want to level the area the best you can with finish so you have enough finish on the wood so you can sand out. Dry runs, use a razor blade in a card scraper fashion working only on the run portion.

Hope this helps.

instead of buying a better sprayer and spraying cheap stuff, why not buy a better water-based product and spray with a cheaper sprayer. The reason a finish is cheaper, is due to "less" goodies contained in the finish. The spray gun/rag/brush/paint roller... gets the finish onto the wood. Then its the finishes job to lay on the wood and flow out really nice.

I agree with Ace. A high quality finish is typically much more forgiving meaning that even if the initial application is less than perfect it will have enough 'open time' to flow out properly. Inexpensive finishes can be very demanding requiring a perfect application in a perfect environment (which very few of us have). I've sprayed high end finishes with less than top dollar equipment as well as cheap finishes with high end equipment. The end result? More often times than not is boils down to the material you're working with and not necessarily the equipment being used. Regardless of the gun you're using a MAJOR factor in how it sprays is keeping it clean. After every use do a full break down and thoroughly clean every part. Use properly sized cleaning needles, brushes, etc with the proper solvent and blow dry before re-assembly. Anyone who sprays knows that a good cleaning kit is worth it's weight in gold :)

As far as thinning I think it's best to only do what is necessary to get the viscosity needed for spraying. There are other factors that play into this if you're working outside in a breeze or a hot day with little humidity but generally speaking knowing how much to add is something that comes with experience. I look at the mixing instructions for a product as general guidelines or a starting point if you're un-familiar with it. From there it's trial and error. When I find a product I like I tend to stick with it simply for the sake of getting consistent results.

There are many very good quality water based products avail, but one that I use that doesn't seem to get a lot of attention is made by Crystalac (avail through McFeely's). Very hard / durable finish, cures water clear which is a nice feature when working with lighter colored woods and is about as forgiving as it gets on application.

Hope this helps!

~Andy

Food for thought...instead of buying a better sprayer and spraying cheap stuff, why not buy a better water-based product and spray with a cheaper sprayer. The reason a finish is cheaper, is due to "less" goodies contained in the finish. The spray gun/rag/brush/paint roller... gets the finish onto the wood. Then its the finishes job to lay on the wood and flow out really nice. Less goodies means less stuff on the surface to flow out.

Another thing that often comes with better finishes is support. Email your setup details to a good manufacturer, and they can often have folks who will answer and provide setup details and tips. In my case, I happened to buy my Fuji 4 stage from a dealer who was also a hands-on finisher / refinisher, and he recommended products that he used every day in his own business. He didn't sell any of those products, so I felt the recommendations carried a bit of extra weight.

Yet another thing is consistency. I can take notes, including atmospheric conditions, with a pro finish, use those notes to set up a year down the road, and they still apply perfectly. I HAVE gotten good results with home center materials, but I've also seen wide variations in product.

One thing to keep in mind with water base is that you should always test a finish / material combo on scrap before you shoot a project, even if you've used the same finish on many other materials. For example, my favorite finish looks GREAT on white oak with a few drops of amber dye, but it can turn cherry gray if a shellac barrier is not used.

  • Author

Thank you all, for all your help. I have wasted countless hours on the internet trying to find answers to these questions. The reason for the water-based finish is to preserve the light color of the birch. I will post some photos and Skechup plans soon.

Again, thanks

Where do you find pre-finished?

I buy mine at CT Wood Group in Enfield, but that's a haul and a half for you. This is a very popular product, General Woodcraft probably carries it.

If that fails, check out Eastern CT Craigslist under Materials. There's a shop in SW RI that advertises cabinet and furniture making supplies often. I've never dealt with them, but they look like they could be a decent source.

I've done business in the past with The Wood Rack in Branford... http://www.thewoodrack.net/index.html His site is way out of date, but he might be worth a call.

  • Author

thanks again, your right about General Woodcraft. They can most likely get it. Do you know a local source where I can buy sheets of high pressure laminate like Formica, I am looking for solid colors not the fake looking stone?

thanks again, your right about General Woodcraft. They can most likely get it. Do you know a local source where I can buy sheets of high pressure laminate like Formica, I am looking for solid colors not the fake looking stone?

The best source I've found is my local Lowes kitchen department, where they take orders for custom cabinetry. All the samples are on the wall. They haven't had an issue ordering sheets of raw material for me. I've previously used a local lumber yard, but in this case, Lowes has provided excellent service.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.