Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Ridgid R4512 clicking/slapping sound trouble

Featured Replies

Ok so I was buzzing through some thick wood yesterday and it bogged the saw down to the point of throwing the electric breaker. Stopped. So I plugged it into a different socket and continued to saw away. Everything was fine. Except after that incident a little while later I started to hear what I can only describe as a repetitive clicking/slapping sound when the saw gets going. Think bicycle card in wheel sound but not so slappy if that makes sense. It is not entirely like a clicking sound either, but maybe you get the picture.

The saw still cuts fine without any noticeable loss of power, yet, but I would like to know what that sound is so I can fix it before it becomes something bad. I took the insert off and blew everything clean with air which did not change anything. I switched blades and the sound persists, so I do not think the blade is thrown out of flatness. Haven't gone any deeper than that yet. Any suggestions?

  • Author

I was thinking it might be a drive belt thing. But would that one meltdown be enough to make a flat spot? The saw is only 1 month old. Would like to get more info before I turn this motherload upside down as it something I only want to do once. Wish it had a top that opened to get inside the motor from the top.

Just to cover the bases, did you check that a sliver of wood isn't stuck somewhere?

  • Author

Yeah. Blew out the motor with air, cleaned and lightly oiled the arbor just for good measure, and checked for debris.

Check the belt. You don't need to flip it over. Pop the access panel off of the side. Also does the noise increase with blade speed? Is it present only when the motor is running, or is is present on blade deceleration after the saw is shut off?

  • 5 months later...

So, Midtone, did you ever track down the source of that clicking in the Ridgid 4512?

I've encountered the exact same thing. Saw about a month old. Working through a heavy piece of maple.

 

I haven't removed the belt yet, but I did remove the back panel. Removed the saw blade, then I noticed, turning everything slowly by hand, that the click is timed with one revolution of the motor pulley--not the belt, so it doesn't seem like it's caused by a flat spot on the belt. The sound is metallic--something slipping, clicking into position. Very slight sound, telegraphs through the whole trunion structure so very hard to pin down the source.

 

But the timing of the click with the motor pulley and the distinctly metallic sound---makes me think (ugh) it might be bearings.

 

Appreciate any wisdom you or anybody else may have.

I have that saw. I actually had the same problem, and found the weld on the motor fan broke. The motor fan blade was just flopping around on the motor shaft. Luckily the saw was new, and they allowed me to exchange it. If you are looking through the back cover, the fan cover is on the far right side of the motor.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.