Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

My planer removes more wood from one side of a board than the other????

Featured Replies

I have a Ridgid TP1300 13" planer. i was making a cutting board the other day and i ran the board through my planer to clean things up (while it was still in a long grain orientation). after the board was nice and flattened, i checked it with a caliper on all four corners to ensure i was getting a consistent thickness. the right side of the board was approximately .5mm thinner than the left side. the board was the full width of the planer (13"). i looked in my owners manual and it lists this as a potential problem and says the fix is to adjust the elevation screw. however, i can't find how to do so anywhere in the manual. and btw, i know that .5mm across 13" doesn't sound like a lot, but when i take this board and cut it into strips so i ca flip and expose the end grain, the error will be multiplied and i will not end up with a square cutting board. anyone know how to fix/adjust this?

Whenever I experience problems with my planer (same one as yours), my first course of action is to clean it really well. Take the back off and clean the blades, the rollers, and all accessible parts. This is often enough, in my experience, to solve most issues I have had. If this does't work, then start checking alignment screws and such.

  • Author

I've cleaned it. Rollers and all with mineral spirits

Check the instruction manual on adjusting the table on the bottom. I bought my planer second hand and had the same problem. The instruction manual had a procedure documented that involved laying the planer on it's side to make said adjustments. It's not the same make though and I'm not sure if the bottom table on the ridgid is adjustable at all.

Height adjustment system might have slipped on one side. Measure or count threads and see if it just needs to be tweaked a turn or so only on one side. Might have to disconnect the sprocket/ chain etc....

  • Author

i've checked the blades. they are properly aligned. i believe the entire cutter head is lower on the right side. i was just hoping someone out there had adjusted one of the elevation screws before. i will just have to tear into it and figure it out as i go. now, i just have to find the time to do so.

Do you live near a ridgid authorized service shop? If so, you may want to save yourself the hassle and use the LLSA offered by ridgid.

I had the same problem with my dewalt 733. I cant remember what i did but it was quick and easy. The head was lower on one side. I think i took the bottom off and loosened a collar of some sort and used the height crank to level the head. I did a google search and found it.

-Jason

  • Author

i called ridgid and talked to tech support. called 2 separate times to see if the procedure varied, and not surprisingly, it did. i may call back a third time to see what they say, just for giggles. more often than not, if you want something done right, you have to do it yourself.

i called ridgid and talked to tech support. called 2 separate times to see if the procedure varied, and not surprisingly, it did. i may call back a third time to see what they say, just for giggles. more often than not, if you want something done right, you have to do it yourself.

Forget tech support. Bring the whole unit in to the repair place and have ridgid foot the bill under the LLSA.

  • Author

Forget tech support. Bring the whole unit in to the repair place and have ridgid foot the bill under the LLSA.

that would be nice, but i don't believe this tool is covered under said agreement.

that would be nice, but i don't believe this tool is covered under said agreement.

Sure is covered! I have the same planer. Email ridgid for a list of approved repair centres. They will ask you if you registered the planer (hopefully you did). If so, then they will repair or replace it.

When I contacted Ridgid for service on my jointer, they said that I wasn't covered because I wasn't the original owner. The original owner sent in the bar code from the box to register, so even if I had gotten the box when I bought it, I wouldn't have gotten the bar code. No bar code, no registration, no lifetime warranty.

Kinda reduces the resale value, if you ask me.

When I contacted Ridgid for service on my jointer, they said that I wasn't covered because I wasn't the original owner. The original owner sent in the bar code from the box to register, so even if I had gotten the box when I bought it, I wouldn't have gotten the bar code. No bar code, no registration, no lifetime warranty.

Kinda reduces the resale value, if you ask me.

Bummer. This has happened to me with a drill press. I bought it 2nd hand as well, but I did so knowing that the LLSA was null. I hope the OP is the original owner of his planer!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.