Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

finishing figured cherry

Featured Replies

Obviously I'll be doing some tests on scraps first, but I'm hoping to get a few ideas from you guys to try...thanks y'all.

post-7224-0-30027200-1356014954_thumb.jpEric I just finished a humidor with a figured cherry top, with walnut trim. The picture doesn't really do it justice (cell phone camera), but the figure pops pretty well. I used a sanding sealer, rubbed on, sanded back down to 400 grit, and then I used a clear satin lacquer.

I did leave the cherry out in the sun for two days before I lacquered it to darken it up a bit. This was mainly to make it match the other cherry on the sides of the humidor, but the "cat's eye" (don't know the non-slang term for it) really popped after sitting in the sun a bit. You can see it in the top of the photo, its on all of it, but lighting sucks in my basement.

I'd be real careful w/ cherry... Figured cherry can look awesome, but it tends to blotch like crazy. I've probably made a dozen pieces in either figures or spalted cherry in the past four years, and have found a process that I've standardized. The process I use trades some of the 'pop' I would get with a more aggressive approach for a non-blush surface.

Spray a 1# SB to seal it and lesson the chance of blotch. I spray another 'lightly tinted' #1 SB as a tone to even-out sap and multi-panel glue-ups -- it will also absorb into the figure a bit more then background because the initial 1# doesn't seal the figure completely, just the 'background'. The amount of dye I use in the tone is really light -- I just trying to 'even everything out' -- again blush-adverse. If I want it a bit darker, I leave it outside in the sun for a day prior to top-coat. For pieces that are going to see some use, I spray three light coats of pre-cat 336 clear, then rub to whatever I want. For decorative pieces, I use Sutherland Welles tung oil.

I have a board of moderately figured cherry that I'm planning to use in my next project, and I can't decide how I should finish it. I'd like to accentuate the figure as much as possible, but still avoid the blotching for which cherry is notorious.

I'm considering starting off using the "pop the maple" approach seen in Marc's video...a little Transtint mixed in dewaxed shellac. But then what? If I sand back and apply an oil based finish, what results should I expect? Blotching? Maybe sand back then apply a second coat of clear shellac, then varnish?

It's tough to know how to proceed here...how do I pop the figure (which is essentially a kind of blotching, yeah?) but still avoid the regular ugly blotching we get with cherry?

Obviously I'll be doing some tests on scraps first, but I'm hoping to get a few ideas from you guys to try...thanks y'all.

Buy a can of Charles Neal's blotch control. It's a water based application that works great. It will raise the grain after each application so a little light sanding between coats will be necessary. Most of my projects are made from cherry. I built all my kitchen cabinet doors from cherry and used Neal's blotch control on all of them. No blotching!

Happy building!

  • Author

Good tips, I'll try them both. Unfortunately I'm relegated to wipe-on because I have a spray system problem at the moment...as in I don't have one. <_<

Buy a can of Charles Neal's blotch control. It's a water based application that works great. It will raise the grain after each application so a little light sanding between coats will be necessary. Most of my projects are made from cherry. I built all my kitchen cabinet doors from cherry and used Neal's blotch control on all of them. No blotching!

Happy building!

I've finished some cherry in the past and had success preventing most blotching with shellac. I was just curious if there was a good way to pop the figure and prevent blotching at the same time. Sounds like a bit of a catch-22 situation.

if you think about it, a 'pop' is a selective blotch... I only try to balance the two. If you have some scrap, you could try the sand-it-back method... But I think the risk will always be there that some background will always blotch unless you sand-back a lot...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.