Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

ROS Opinions? (I need a new one)

Featured Replies

My Milwaukee 6021-21 is just about shot I think. It's not so random any more, and I'm sure that's because the bearings are just about shot. It's not an expensive enough tool, to be worth having refurbished or anything like that, so it's time for a new one.

Festool isn't in my budget, nor is the Mirka Ceros. What do people think of the Porter Cable 390K, or the DeWalt D26456 (looks to be the 390k but yellow)? Any other models I should consider?

I have the low profile PC and love it. I bought it while my old PC sander was in the shop for repair brought it home used it on a project and my brother went and bought a second for the shop that day.

I have the DeWalt D26456, and I love it. The dust collection is impressive for it's price point.

  • Author

How long of you guys had your low profile sanders, since they are the same sander? My biggest concern is that it randomly oscillates throughout it's life. Pretty much every ROS I Have ever owned always becomes an angle grinder even with proper maintenance.

I've had my low profile 5" PC ROS since they first came out a few years ago and it still Randomly orbits fine, and I love the dust collection when attached to a hose to my shop vac. Catches all the dust ! The top or grip is a tiny bit on the big side ,so if you have small hands then it might be uncomfortable over long usage, other than that it's the best ROS I've ever owned. I had PC's older model RO sander for more than 20 years( The one with the side handle) and it never stopped orbiting randomly, so I can't relate with your past excperience. I still have this old sander. I replaced some gears on it that wore out. I also have one of the yellow Dewalt RO sanders , but it stopped working .

Ill tell my long winded sander adventure. Prior to my shop torching I owned all festool, they were great and did the job. While rebuilding I did the research and decided mika was the way I was going to go. The problem was my dealer didnt have them yet so I bought a six pack of pc low profiles. My train of thought was that they were just cheapo pc's and they wouldnt hold up. I started back up with the pc's and lthey were doing just fine when my tool dealer called and said Mirka's were in stock. I took a demo to try out, I was impressed but treated it like a first newborn since it was a demo and not mine. I then purchased 2 Mirka's and proceed to use them on a big reface order a 104 unit apartment complex thats alot of doors. Half way through the doors both sanders started to rattle and slow down. I returned them thinking for that kind of money they should have held up better. I finished the job and a couple other smaller jobs with the pc's and they are still working just fine. These are the first two pc's, four are still unused brand spankin new. I was wrong about the pc's they have proven to be good sanders.

The dust collection is real close to the festool and my shop shows it. One thing people dont keep in mind when comparing dust collection is the vacuum. Most hook up a shop vac to a non festool sander and have a thin layer of dust all over their shop and blame the sanders ability. Most of the time its the vacuums exhaust that sends that dust flying all over the shop and the simple cure is a drywall bag along with the pleated filter. The drywall bag will make any vac filter the fine dust just like the festool vac. I installed a heppa kit in my fein and low and behold the elcheapo pc's really shine in the dust collection department. Now that my hands are deformed from DJD and not working the pc's have proven to be a good fit with their chunky top.

Don

==> a big reface order a 104 unit apartment complex

now that's a lot of sanding....

I have all FT and Ceros at this point.. I have 1 remaining PC 5" lowprofile that I'm going to eBay. The sander is almost new, but I only want to inventory 1 hole pattern of paper... I use the mesh on the Ceros.

Don I just have to say it is so awesome to have you back :) thanks for sharing your knowledge.

  • Author

Don,

Thanks for the insight that's the kind of feedback i was looking for., I'm definitely going to get the low profile PC as soon as my local Menards has it in stock again.

  • Author

How about a cabinet scraper ;).

I got one of those, and it gets used all the time. It doesn't do so well(last)on stuff like Jatoba.

I got one of those, and it gets used all the time. It doesn't do so well(last)on stuff like Jatoba.

Fair enough!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.