atratinus Posted January 10, 2013 Report Posted January 10, 2013 Let's assume you have, essentially, no shop space and you must rip and crossut cab-grade plywood to size. Your budget won't allow for a decent miter saw and a table saw is out of the question. Which sort of saw would you purchase for breaking down plywood goods: a circular or jigsaw? Speed, btw, is not an issue; I'm just looking for the cleanest, assembly-ready cut. This is not Stickley furniture (love it), but basic homeowner furniture. Thanks for entertaining a newbie. Quote
robjeffking Posted January 10, 2013 Report Posted January 10, 2013 Circular saw faster,cleaner more accurate straighter cuts. A very simple plywood jig can be made for making straight cuts. Quote
Colorado Brian Posted January 10, 2013 Report Posted January 10, 2013 I would go with a track saw (circular saw with integrated straight edge) Festool is #1 but Dewalt also makes a quality saw. There is also a new post about one made by Grizzly. I have the Festool TS55 and I couldn't be happier with it. Marc did a video comparing the two a while back that should still be on the WoodWhisperer site Quote
Chris H Posted January 10, 2013 Report Posted January 10, 2013 I would go with a track saw (circular saw with integrated straight edge) Festool is #1 but Dewalt also makes a quality saw. There is also a new post about one made by Grizzly. I have the Festool TS55 and I couldn't be happier with it. Marc did a video comparing the two a while back that should still be on the WoodWhisperer site I am guessing if the budget requires a decision on circular vs jig, then track saw is completely out. They run more than an entry level table saw, which I'd recommend before a TS. Don't get me wrong, I love track saws (wish I owned one), but I don't think it's the solution here. Circular saw, definitely. The jig will bounce all over, even with a good guide setup, it's designed to make curves and turns while cutting, the circular on the other hand is designed for a straight cut. 1 Quote
Mister Pants Posted January 10, 2013 Report Posted January 10, 2013 Obviously a track saw if the budget allows, but I'm guessing not. In that case I'd say a circular saw and a straight edge. If money is really tight you can use a piece of jointed wood or even a metal stud with clamps for your straight edge (used both in the past and they do work) and splurge a little on a half-decent high tooth blade (the Freud diablo style for instance). Quote
CessnaPilotBarry Posted January 10, 2013 Report Posted January 10, 2013 Circular saw. then... Make a straight edge. Like this: http://www.popularmechanics.com/home/reviews/4283497 The first cut will make it match your saw perfectly, so you'll know exactly where to clamp it. You can make a sister for it for you router, once you get a router. I have thousands of dollars of equipment to make straight cuts, but I still use something like this away from the shop. I prefer to use mine on the floor, on 2" thick blue foam insulation, instead of horses. Quote
rodger. Posted January 10, 2013 Report Posted January 10, 2013 +1 on circular saw. Jigsaw blades can wander, even when using a fence. Quote
Beechwood Chip Posted January 10, 2013 Report Posted January 10, 2013 Does a circular saw with a guide create an edge straight enough for cabinet work, or do you have to clean it up on a table saw? Can you run plywood through a jointer? Quote
rodger. Posted January 11, 2013 Report Posted January 11, 2013 Does a circular saw with a guide create an edge straight enough for cabinet work, or do you have to clean it up on a table saw? Can you run plywood through a jointer? Running plywood over the a jointer would wear the blades very quickly. I would never run plywood over the jointer. Quote
CessnaPilotBarry Posted January 11, 2013 Report Posted January 11, 2013 Does a circular saw with a guide create an edge straight enough for cabinet work? It certainly can... I've built built-ins on site this way. The saw needs a decent blade, and the stock needs to be cut face down. If it's a poor quality saw, edges can be quickly squared up with a router and straight bit. The router can also do dadoes and rabbets where needed. This is not the preferred, or most efficient way to work, but it certainly can work out. If I were doing things this way, I'd probably devise a spacer system to install shelves or shelf cleats, pins in holes, or use metal tracks for shelves, rather than trying to make mirrored dadoes. Quote
atratinus Posted January 11, 2013 Author Report Posted January 11, 2013 Thank you all for the advice. I had essentially already decided on the circular, but thought perhaps that a jigsaw's flexibility might be an advantage. In any case, I got the Kreg Rip-It for Christmas, so the circ makes that much more sense. I have read about the straight-edge jig for the saw that Pilot Barry mentions, and will probably use the Rip-It for rips and the jig for crosscuts. Once I get the saw, I'll get the Diablo 40-tooth and employ a technique I've read about, scoring with a very shallow cut before making the full cut. I hope this will suffice for the time being to make a decent tv stand and a couple bookshelves. On a related note, I do in fact have a palm router; if the setup described above yields more chipout than is tolerable, would a flush trim bit help or simply make for additional chipout? I look forward to trying this first project; thanks again for everyone's help. Quote
tdale51@yahoo.com Posted January 11, 2013 Report Posted January 11, 2013 to help with splintering you can also double face tape a piece of hardboard to the sole of your circular saw. Then plunge the blade through it to create a zero clearance insert of sorts. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.