Recommended Posts

Posted

PhotoMar0471503PM_zpsb58c82c3.jpg

 

Festool ETS150/5

 

It is amazing. Tested it with the sample paper that came with it, and it is just fantastic. I just put the bag on it because I don't have a Festool vac, and I didn't want to get my shop vac set up now.

Posted

I got one of those after I wore out 3 Bosch random orbit sanders. Get the narrow hose and hook it up to your vac. I drilled some holes around the edge of the hose fitting to reduce the suction, it was wearing out the Velcro pad too fast when the suction was too high. I did some comparison tests and the Festool sandpaper does cost more but it lasts much longer, about 30% , so it actually reduced my abrasives cost. Had it over 5 years in a small custom cabinet shop.

Posted

I got one of those after I wore out 3 Bosch random orbit sanders. Get the narrow hose and hook it up to your vac. I drilled some holes around the edge of the hose fitting to reduce the suction, it was wearing out the Velcro pad too fast when the suction was too high. I did some comparison tests and the Festool sandpaper does cost more but it lasts much longer, about 30% , so it actually reduced my abrasives cost. Had it over 5 years in a small custom cabinet shop.

Do you use it with a Festool vacuum? Only reason I ask is because the vacuum has variable suction control which I assume would help with the wear that you posted about. I don't have their vacuum yet, so I will probably use the hole in the hose idea.

Posted

==> I drilled some holes around the edge of the hose fitting to reduce the suction

 

now why didn't i think of that...

 

==> Do you use it with a Festool vacuum? Only reason I ask is because the vacuum has variable suction control which I assume would help with the wear that you posted about.

 

I have several FT sanders and several CT vacs... and even with a CT on 'turtle', there is sometimes too much suction...

Posted

==> I drilled some holes around the edge of the hose fitting to reduce the suction

 

now why didn't i think of that...

 

==> Do you use it with a Festool vacuum? Only reason I ask is because the vacuum has variable suction control which I assume would help with the wear that you posted about.

 

I have several FT sanders and several CT vacs... and even with a CT on 'turtle', there is sometimes too much suction...

That's actually good to know :) Thank you.

 

Let me just say, I tested this thing with the supplied 80 grit granat paper, and it make some hard maple turn to dust like no other. Then I worked through the 120 and 180 grit (also supplied) and the surface was amazing even at 180 grit. I can't wait to get my order of 220 grit in the mail.

Posted

==> That's actually good to know  :) Thank you.

 

Yea, if the CT's added a 'snail' setting, then the problem would go away.  With the current setup, there is still too much suction for fine sanding in some situations.. . Not that often, but often enough to be annoying...

Posted

==> That's actually good to know  :) Thank you.

 

Yea, if the CT's added a 'snail' setting, then the problem would go away.  With the current setup, there is still too much suction for fine sanding in some situations.. . Not that often, but often enough to be annoying...

How can you tell if there is too much suction?

Posted

==> How can you tell if there is too much suction?

 

You can easily test for yourself.  If you take your 150/5 and run it on a CT with full power (‘rabbit’ setting), you’ll get excessive abrasive wear, excessive vibration/‘skittering’ (if that’s the right word) and swirl marks even with no applied downward pressure and using good RoS technique.

 

As you back-off the suction, these conditions will subside and, in most cases, completely disappear when you get to the lowest setting, ‘turtle’.  However, they may not completely disappear, which is why I wish there was an even lower setting….

Posted

We wore out the Velcro pads too fast , had it hooked up to a Fein vac. Drilled holes in the hose fitting near the tool. Found a scrap of plastic pipe that almost fit around the outside, sawed a kerf 3/4 in so it was a tight fit collar Drilled thru both , shift the collar to use on the Domino or shop clean up at full suction. The tool triggered start failed on the Fein and one of those Mbrite factory rebuilt devices fixed the problem.

Posted

==> Drilled holes in the hose fitting near the tool. Found a scrap of plastic pipe that almost fit around the outside, sawed a kerf 3/4 in so it was a tight fit collar Drilled thru both , shift the collar to use on the Domino or shop clean up at full suction.

 

I was going to ask about control... I was thinking about some sort of sleeve fitting -- like on my home vac... Your solution sounds similar...

Posted

It gives some control. Holes open for sander, covered for Domino. Halfway covered makes an annoying whistle!

Playing with a CT 26 Festool vac this week. Too many times we have needed to use both tools at the same time.

Posted

I've got a 26 or two.  They are great -- the boom arm is a good accessory.  I use the Oneida UDD on both my 26s -- an expensive option, but really works well on the 26...

Posted

Other than a vacuum and some clamps, there really aren't any other tools that I "need" right now. I can get by with what I have to make some projects.

 

Next tools on my list are a drill/impact driver set, pocket hole jig, band saw, and a router. I am going to try and see if any of those tools at my grandpas are still in working condition. If not, I guess I can wait :)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 35 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined