Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Shop Electrical Question

Featured Replies

We our building a new home, and for the first time ever I am getting some dedicated shop space, very excited!  I don't currently own any tools requiring 220, but I am planning on getting a cabinet saw soon, so I asked the builder to install a 220v outlet in the garage.  I checked last weekend and they had installed the 220, but the outlet is the same as a dryer outlet.  I am assuming that this isn't correct, and that the outlet should look more like a standard 110.  Any help is appreciated, even a picture.

 

Thanks.

Depends on the amperage needs of the tool. There are several different 220/240 volt plugs. The dryer outlet is probably for a much higher amperage than you will need. At least that means the wire he ran should be big enough for anything you get, the outlet and breaker can be swapped easily. You do not want too large on the breaker.

Look at the specs on the saws you are considering for the reccomended size and type of breaker required. Some tools need a surge at start up.

==> The dryer outlet is probably for a much higher amperage than you will need.

We've got gas, so I've no idea..  What's a dryer line these days? 10-2?  NEMA what?  

==> The dryer outlet is probably for a much higher amperage than you will need.

We've got gas, so I've no idea.. What's a dryer line these days? 10-2? NEMA what?

The dryer outlet line in my house looks much larger than 10/2. Unless there is a huge jump from 12/2 to 10/2.
  • Author

I will check this weekend on the amperage of the breaker.  I am planning on getting either a Powermatic or SawStop 3hp single phase cabinet saw.  I guess I expected the 220 outlet to look more like the picture below.

post-3491-0-99324700-1362582254_thumb.jp

Most of the time a 220 line will be wired with 8/3 able to support 40 amps. I think the plug is a oven type that you have you might want to have both receptacles. I have both and it has come in hand more than once

They are placed close to each other and close to the panel so there wasn't much cost.

I will check this weekend on the amperage of the breaker.  I am planning on getting either a Powermatic or SawStop 3hp single phase cabinet saw.  I guess I expected the 220 outlet to look more like the picture below.

Like Triple H said, that is a NEMA 5-20, unless the horizontal input is on the other side. For a 220v tool, you will need a NEMA 6-20.

 

The oversized wire actually works to your advantage. You will never have to worry about the wire, if installed correctly. The outlets and breakers are extremely easy to install, just good luck with bending the wire to fit into a box with that thick of wire. I had a hard enough time with 12/2 wire. I cut the stuff too long, and the slack wouldn't fit, so I had to cut some off. I repeated this 2 more times until I finally had enough room.

Josh,

I went through the same process, with the same result. I've had the electrician come back to the house and put in a sub panel at the site of the 220 socket. As 220 tools draw significantly less current (usually half) we split the power feed into one side for 220 tools ( three 20 amp circuits) and the other side to supply 3 additional 115v circuits. This lets me run my 220v joiner and provides for the future 220v table saw and dust collector. I hope this is of help to you. CHEERS!!

 

Gerry

==> unless the horizontal input is on the other side

just an orientation thing, it's still a NEMA 5-20R

==> unless the horizontal input is on the other side

just an orientation thing, it's still a NEMA 5-20R

Sorry, should have been more clear. There will be an alone horizontal line on the right side (if you are looking at the plug in the wall), it will not form a T. The left will look the same.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.