Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Two coffin planes - Rehab or Rubbish?

Featured Replies

Some time back I purchased a group of old woody planes on eBay that were a bit rough, but hopefully serviceable. It seems neither is as serviceable as I had hoped so I am seeking advice before I put any more time or money into these planes. I've only got about $10 into the pair of these so I'm not keen on spending money on them unless I can be sure of a good result.

 

While cleaning up the iron in one of the two small coffin planes I noticed a hairline crack in the iron about 1" back from the cutting edge that causes the end of the iron to bend about 3/32" towards the wedge. I'm thinking that this iron won't ever bed properly and I'd get lots of chatter. This plane is shown below.

post-7229-0-98016700-1363826411_thumb.jp

 

The second coffin plan has many cracks and splits in the body (some filled with epoxy) and would need a new wedge as it has shrunk. The iron and chip breaker look ok, but there is a fair amount of pitting on the back of the blade.

post-7229-0-83547600-1363826413_thumb.jp

 

The options that I can think of are:

1) Use one or both planes as-is for now?

2) Get a new iron for the first plane from LV for $37?

3) Make a new wedge for the second plane and use it?

4) Put the iron from the second plane into the first one (would need to trim about 1/16" so it fits)?

5) Dump them in the trash and try again?

Hi Steve M,

 

How about making 1 new wooden plane body and use the one good blade? I find myself in a similar situation. I have a rough old worm eaten jack plane. I intend to slice it down the middle and use the two halves as a template to make two new halves I will then laminate the two pieces together. I intend to start that project in a Month or so so if you are in no hurry we could try and build them at the same time and see how it goes.

The smoothers are not really interchangeable. One uses a chip breaker (there is a slot for the screw) and the other is a single iron plane (no slot).

 

There are two possible issues with old coffin smoothers. The first is that the wedge may have caused a crack at the shoulder. If so, this is rarely repairable. I cannot see such a crack in the photos, so they may be OK.

 

The second issue is that the mouth enlarges as the sole wears (or is planed down). The fix for this is a patch over the mouth. This usually returns the plane to full use.

 

They look to be nice planes.

 

Keep an eye out on my website in a few weeks time as I shall be posting a pictorial on building coffin smoothers from solid wood.

 

Regards from Perth

 

Derek

  • Author

Thanks for the suggestions, but I'm trying to get a working plane with minimal effort and expense. I happen to know you can remove the cap iron and put the blade in a plane designed to have a single iron because Bob shows one of his planes being just like that in a podcast. He also says all of his woodies, including smoother, has a wide open mouth so I'm not going to do anything about that.

 

My plan for now is to keep an eye out for a cheap alternative on eBay and in the mean time try to straighten the iron without breaking it on the hairline crack. Failing that I'll make the slightly wider iron (sans chip breaker) fit the better body of the single iron plane. Thankfully the iron in the try plane looks good and a few whacks on the iron if the fore plane took the bend out of it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.