Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Gloss finish issue (Arm-R -Seal)

Featured Replies

So i just built my version of the weekend wall shelf out of cherry and i've applied 6 coats of gloss Arm-R-Seal now. The problem is it is a completely flat surface yet. i can still see pits almost as if it's an open pore wood. i did thin the varnish by about 10% on all coats to help it flow a bit better. Should i just go full strength and keep applying more until its all level? I don't want to put too many more coats on since i think it'll start to get too thick. Thoughts?

post-6735-0-53633000-1364435598_thumb.jp

Sir, I usually start with several coats of shellac before applying a top coat for it's fill qualities. It builds up faster in the pores so you can reach that glass smooth look sooner. If you are afraid of adding too many coats, sand several  coats off so that all you leave unsanded are the pits. Then reapply your finish coats, sanding in-between, until it smooths out.

If you're looking for a smooth /glass surface, it's all about build up.  Not necessarily after the grains are filled (well, maybe depending on the look you're going for) but at least enough to fill the grain.  Only one way for that to happen.  Lay it up, knock it down..  Repeat as necessary..  A pre finish such as shellac or sanding sealer may help.  Also, sanding the bare wood to a very fine grit if a glass surface is what you're going for.

 

I would suggest that you not add thinner and apply the finish slightly heavier.  It may initially have small bubbles and look a little 'off', but the finish WILL flow out and allow the trapped air to pop. 

 

The key is to NOT work it too much; the more you work the finish the faster the solvents evaporate from the surface (reducing it's ability to flow and level out). 

 

Lay it on the best you can and let the finish do what it's formulated to do :) ..  The nice thing about this stage of the game is that if you're not happy with the result, you can knock it back down and try again :P ..

  • Author

Boatworks, i think you nailed it on the head. I have been working the varnish a bit too much. I'll apply another coat or 2 and will only wipe it once and see if that helps. Thanks!

Block sand the finish with 600 wet/dry paper, stay off the edges. The goal is to level the finish and be careful of sand-thru's.  Then apply the Arm-R-Seal straight from the can, no thinning. Wipe it on and leave it alone, let the finish level off. May take a coat or two more.

 

What is happening, the finish is building higher around the grain pockets and the grain pockets are pulling the finish down into the wood. So block sanding will knock down those high spots leveling the finish. The pores of the wood take longer to fill up when you thin the finish.

 

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.