Recommended Posts

Posted

I'm trying to learn how to cut dovetails by hand. I find it somewhat difficult to get my saw started on the end grain. Furthermore, once i do get it started, its usually half a milimeter off from where i wanted to start the cut. I'm wondering if I can mark the start of my cut with a chisel and light mallet blow. It seems this technique would allow me to start the cut right where I want. Just thinking out loud. Will this idea hold water?

Posted

Give it a try Nick, you could use your marking knife and square too. Also if you use the tail board as the template it does not matter if the cuts are not exactly to the mark as long as the cut is square. And if you use a sturdy marking knife to transfer the tails to the pin board you have your knife mark ready to go.

Take a look at this video and go to 5:50. It might be over the top to start a dovetail saw this way but you could do a smaller version. 

If you can keep practicing without the above it will make things a bit more rapid. Keep on practicing  ;)

Posted

Being a little off is not a big deal, as long as you always leave the line.  You are likely going to be cleaning up with chisels.  Usually when i have trouble starting the cut, its due to the fact that I pushing the saw too hard, and have too tight of a grip on the saw.  Loosen the grip, and let  the saw cut, rather then trying to force it.  You will be amazed at the difference it makes!

Posted

I'm trying to learn how to cut dovetails by hand. I find it somewhat difficult to get my saw started on the end grain. Furthermore, once i do get it started, its usually half a milimeter off from where i wanted to start the cut.

 

So that's why you don't want to start the cut right on the end grain. It's like having a high degree of difficulty and getting the East German judge at the same time.  ^_^

 

It's better to start the cut on the near corner, with your (presumably western) dovetail saw held at an angle so that the handle is down and the toe of the saw is up. That way, when you start the cut, you'll be cutting somewhat with the grain, which is much easier than cutting across it. You can see what I mean at 5:00 into this Lie-Nielsen video on making a half-blind dovetail.

 

(Of course, the main reason for angling this saw in this video is because you're sawing part of the wall of the pin board, and you have to angle the saw since it's a half-blind. But it's the best illustration that I found. And in this video they do mark the lines with a knife, but that's not the main point I'm making. You can do this with pencil lines as well.)

 

Once you get the saw cut started, try to make sure you're hitting both lines with your cut, and then you can level out the saw and work your way down the rest of the cut. And with more practice, you'll be able to start the cut more across the grain. But this is a good way to get going.

Posted

Give it a try Nick, you could use your marking knife and square too. Also if you use the tail board as the template it does not matter if the cuts are not exactly to the mark as long as the cut is square. And if you use a sturdy marking knife to transfer the tails to the pin board you have your knife mark ready to go.

Take a look at this video and go to 5:50. It might be over the top to start a dovetail saw this way but you could do a smaller version.

If you can keep practicing without the above it will make things a bit more rapid. Keep on practicing ;)

Thanks! I love watching Roy!

Posted

So that's why you don't want to start the cut right on the end grain. It's like having a high degree of difficulty and getting the East German judge at the same time. ^_^

It's better to start the cut on the near corner, with your (presumably western) dovetail saw held at an angle so that the handle is down and the toe of the saw is up. That way, when you start the cut, you'll be cutting somewhat with the grain, which is much easier than cutting across it. You can see what I mean at 5:00 into this Lie-Nielsen video on making a half-blind dovetail.

(Of course, the main reason for angling this saw in this video is because you're sawing part of the wall of the pin board, and you have to angle the saw since it's a half-blind. But it's the best illustration that I found. And in this video they do mark the lines with a knife, but that's not the main point I'm making. You can do this with pencil lines as well.)

Once you get the saw cut started, try to make sure you're hitting both lines with your cut, and then you can level out the saw and work your way down the rest of the cut. And with more practice, you'll be able to start the cut more across the grain. But this is a good way to get going.

I find it difficult to start on a corner, but I've never tried it with the handle low and blade tip high. I'll give it a go!

Posted

Nick, go to youtube and search for Paul Sellers. He has a video on making a shooting board and in the video he uses a chisel to start his saw cuts. It's easy.

I've just recently discovered Paul Sellers. He's great to watch. He makes everything look so easy. That's the mark of a true craftsman.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 59 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined