Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

bubbles when spraying

Featured Replies

Im spraying a waterbased product called Aqua coat table top semi gloss.  And im having a real problem with bubbles forming in my finish...anyone have any idea how to combat this.  Its 68 degrees in my shop and 35% hum.  any help would be great

I don't have a ton of experience spraying water based products but i have a few questions.  What type of sprayer are you using?  Are you thinning the product? if so how much?  Did you apply a stain before spraying the clear coat?  If so what type and how long did you wait?  Did the bubbles appear on the first coat or on multiple coats?

  • Author

i spray with an earlex 5500 for now...i have 2 coats of stain on and a bonding coat of shelac...i havent thinned my first top coat but i did put a hint of stain in it to even out the stain (toning)  (dark stain over maple...nightmare for blotching)  the toning worked fantastic...color is perfect with no blotching...except the bubbles.  I strained finish through a strainer is this introducing to much air to the product?  There were bubbles in the pot but im pretty sure when the gun atomises the finish the bubles are a nonfacter...im spraying a nice even wet coat.  when i first get done spraying there are a ton of bubles on the surface but i would say 90% of them rise ant pop before dry actually ild say within 2 min after i spray they are gone...but the rest make a perfect finish look terrible...any ideas

Did you tone with Aqua Coat brand of stain? If you didn't, you could have a compatibility issue. Also, check with Aqua Coat if applying solvent shellac is permissible with their product line.

 

Or could be improper gun setup. Here is a test. Do a test board prepped the same way as your project. Use a brush to apply a nice wet coat of the toned topcoat that is giving you issues. If your not getting bubbles with a brush. Could be too small of needle and too much air pressure.

 

-Ace-

Don't shake the can. I had someone shake a jug of lacquer for me figuring it'll be alright. When I went to spray the gun started foaming from the tip. This was with an an Airless system. Had a lot of sanding to do afterwards.

i spray with an earlex 5500 for now...i have 2 coats of stain on and a bonding coat of shelac...i havent thinned my first top coat but i did put a hint of stain in it to even out the stain (toning)  (dark stain over maple...nightmare for blotching)  the toning worked fantastic...color is perfect with no blotching...except the bubbles.  I strained finish through a strainer is this introducing to much air to the product?  There were bubbles in the pot but im pretty sure when the gun atomises the finish the bubles are a nonfacter...im spraying a nice even wet coat.  when i first get done spraying there are a ton of bubles on the surface but i would say 90% of them rise ant pop before dry actually ild say within 2 min after i spray they are gone...but the rest make a perfect finish look terrible...any ideas

 

You should not have bubbles rising and popping finish is not flowing. Bubbles in the cup will cause gun sputter / bubbles. Not knowing anything about the finish. What size needle are you using? What is the viscosity of the finish? 

Try spraying a test board just sealed dont worry about staining. Mix 1/2 0z of half and half to 1/2 qt of your finish. If it works you will have to make some changes to your set up. 

  • Author

could it be possible that i am spraying to much material...my sprayer is not the greatest...no pressure control....a few months ago i was getting alot of orange peel and when i increased the amount of material i was using it went away...could i be on the other side of this now

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.