Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Hardwood or plywood?

Featured Replies

I'm going to be building a jewelry armoire soon. I'm debating using plywood for the sides and then dressing it up or just going hardwood for them. I'm not worried about wood movement of the main carcass. Good idea? Bad idea?

Adam, for something that size, the sheet of plywood will cost you about four or five times as much as using solid wood. That would be my first consideration. A sheet of high grade hardwood plywood usually runs me about $80.00/sht.

I think Troy is right, go solid wood on a smaller case . If you can get a few boards with similar grain then the whole project will look better. A solid wood jewelry case properly made should last for generations. Make sure to sign and date it. I usually write a note telling the wood and finish that was used.

If you're building something that will sit on the top of a dresser, for example, don't bother with the plywood.  

 

I've got scraps of plywood left from a couple of purchases.  I grumbled loud and long (and since then longer and louder) about picking up a quarter sheet of plywood (2'x2' square, actually) for just over half the cost of a full sheet.  At the time, I didn't have the capability of loading a single sheet into or onto my ride for a 15 mile trip back.  

 

If you have other projects in mind to use the rest of the plywood, then and only then would I consider using the plywood.  If not, just go with the hardwood.  It's going to make you happier, it's more portable, its easier to work, it's more fun, and it's more you in the selection of grain, colors, pattern, and style.  I have only found three sheets of plywood in my life that had a grain that I absolutely wanted to display, and two of those got painted.  (The third is sitting in pieces, waiting for me to get back to work on them.)

My issue with plywood is that it sticks out like a sore thumb especially on larger projects. You here folks talk about cabinet grade and using those sorts of terms but that means the inside hidden part of the cabinet not the outside. Plywood is rotary cut so there is no way to hide the fact that its just plywood. There is nothing wrong with using plywood if you dont mind the fact that it will look like plywood. On the other hand plywood is a great material when disguised properly with flat sawn veneer. One  thing that really bugs me is to see someones beautiful expensive custom kitchen cabinets. Then you look at the end panels and they just used rotory cut plywood. Even cabinet doors with flat plywood panels drive me crazy. We all know that the plywood is better in the long run for flat doors like shakers. Especially that darn 5.5 mm stuff that was never meant to be used as door panels. Add two sheets of nice flat sawn veneer to a sheet of 5.5 you get a real nice 1/4" panel that looks like you glued up real wood.

Plywood is simply layers of wood glued together with the grain in each layer at right angles to the one below it. This construction is strong and the alternating grain structure resists expansion and contraction. Construction grade plywood will typically have voids caused by knotholes in the interior layers. Cabinet grade is not supposed to have voids. When I make Arts&Crafts furniture, I usually glue quarter-sawn veneer over plywood.

 

This table uses ash and cherry veneer over plywood. A thin strip of solid wood is used on the edge so I could route a profile. I purposely exposed the plywood on the back to demonstrate the construction of the table.

 

 

P1000615.JPG

 

-Randy

finewoodfinish.blogspot.com

If i were you then I would go ahead and use hardwood. If u decided to use plywood sheet on the side is is more prone to be less solid, and to crack or break under pressure.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.