Andrew Pritchard Posted May 27, 2013 Report Posted May 27, 2013 I got my TS3650 second hand and I love it*. But I wished the dust collection was better. The blade shroud was missing when I bought it, so I made a plywood replacement which is much better. But I still see dust on the floor underneath. Also, the mobile base has been mistreated a bit by the previous owner. It doesn't feel very sturdy (the base can twist a little more than I like) and one of the leveling feet doesn't work properly as it has rusted up. This is fixable, but I'm wondering about a different/better solution. I've just been catching up with some of Jay's Custom Creations**, one of which talks about replacing the mobile base for his saw, which inspired me to consider replacing mine with a similar design. One of the problems I've been thinking about is how the motor hangs at the back of the saw. It's outside the base, which is great because then I won't worry about it clogging with dust and over heating, but the drive belt runs through the completely open space at the back. When you tilt the arbor, of course the belt, motor and blade guard tilt too. I'm not keen on enclosing the motor. 1) It might over heat 2) The blade guard is mounted on it. The solution I've come up with so far is to mount a sheet of steel over the hole in the back, with a curved slot to allow the belt to travel, and then cover over the gaps with sheet magnets. Depending on how hard that is to achieve, I might go with several pieces of sheet steel, and just rivet them to make a slot. Not sure yet. It's the best answer I've come up with so far. What do you think oh-internet-of-much-wisdom? Any improvements? Or am I over thinking this, and really the best option is to build a box over the motor and provide a gap in the top of the box to provide some air circulation and a space for the blade guard to move. I'd want to have a sliding lid anyway so I can take off the blade guard. * Especially compared to the piece of junk Mastercraft I have now collecting dust in the corner of my barn. Probably not going to get rid of it just yet as the TS3650 is not portable. ** http://jayscustomcreations.com Shout out to Jay - thanks dude you've given me some great ideas!! Quote
krtwood Posted May 27, 2013 Report Posted May 27, 2013 It's funny that I've been working on my TS3650 this past week, mainly to replace the arbor and arbor bearings, but also to work on the dust collection since it hasn't been that clean under and inside the saw in years. I'm building a box under the saw inside of the legs. You could just bolt plywood right to the legs, replacing the original brackets, to enclose this in and it would be a whole lot easier than what I am in the middle of, but I wanted the bottom to slope and didn't want to deal with compound angles and I was a concerned if I unbolted the brackets with the saw on the stand the legs would start to slide out but just putting a clamp at the bottom would take care of that. You may have also noticed that the saw will rock front to back without much force on it and that would take care of that problem too. I'll be adding some diagonal bracing instead. Anyway, the reason for the box is that you can't just block it off at the top of the stand because the hose from the dust port hangs down below that, so you have to extend below that. I will run 2-1/2" hose from the port to another port that I'll have on a removable panel on the back of my box. If you haven't had it happen yet, if you drop the arbor nut it goes right down the hose and you have to take your hose off and fish the nut out. Now I'll have a spot where it's easy to disconnect it when that happens. I would have liked to put in a larger port to the box for my dust collector, but with my shop situation I can't get a line to where it needs to go so I have to stick to my vacuum setup. It wouldn't be a bad idea to completely replaced the stand with your own either, but for my part no thanks to trying to move that sucker onto one. Building the box was supposed to be quick, easy, and cheap. Well it was cheap. As far as closing in the top part of the saw, yes to blocking the back off at the saw, no to boxing over the motor. I'm less concerned with completely blocking up the back since it doesn't really throw dust backwards thanks to the shroud. Don't forget to also block off the two areas at the front for the height wheel and the lock knob right under the table. Dust does get thrown at those because the blade shroud doesn't go all the way up. I think the one at the top is the main culprit. I want to get a panel on there that extends into the webbing of the cast iron. I'm just going to glue some magnets into 1/4" ply. As far as the Herc-u-lift, it's sort of touchy how to get it setup. The bolts have to be loose for it to work but you may be able to tighten up something a bit to get it working better, or even loosen something. I remember the one at the store being setup weird and pretty much throwing the instructions away and doing it my own way, but it's been many years. Give me a couple days and I should have it wrapped up and will be able to show some pictures. Quote
Andrew Pritchard Posted May 27, 2013 Author Report Posted May 27, 2013 Jay seemed quite nervous about moving the saw onto his new base, but he managed to slide it from the old base to the new without too much difficulty. If I were to build a new base, I'd probably build it the same height as the legs for the same reason. Like him, I'd like to incorporate a router table into the base. I don't have the money for a full on dust extractor, so I'm limited to a shop vac and Thein style dust bin. It works for me at the moment, but changing the hose when I switch tools is a bit of a pain as I have to kneel down and reach in and underneath the table top. It would be nice if the hose attached to a straight connector at the back of the saw. My I'm glad it's not just me that finds the base a little wobbly! It's hardly surprising given the weight of a cast iron top. Looking forward to seeing the pics! Quote
rodger. Posted May 27, 2013 Report Posted May 27, 2013 This guy did something unique with the 3650. I read this a while back. http://benchmark.20m.com/tools/Ridgid/DcPort/TS3650_DcPort_Modification.html I was also thinking of adapting the overhead shroud to accept a hose. Kinda like this guy https://www.ridgidforum.com/forum/t39946/ Quote
Alan Bienlein Posted May 28, 2013 Report Posted May 28, 2013 Here are a few pictures of what I did to mine. Here it is installed on the mobile base I built for it. Here is a shot of the metal enclosure I did for the back of the saw. No dust escapes from here and I can fully raise and lower along with tilting the blade without having to remove anything. Here are a few shots of what I did for collection under the blade. The piece is removable and the masking tape was used to hold the miters together until the glue dried. A couple of shots looking at the dust collection thru the throat plate opening. And a couple of photos of the routing of my 6" duct work for the dust collection for the saw and router table portion. And the sketchup drawings I did for the mobile base. Quote
krtwood Posted May 28, 2013 Report Posted May 28, 2013 I was able to get it wrapped up today, for now at least. Overall view of the table saw area. You can't see it in the picture but I have an overhead guard that is actually mounted to the ceiling and telescopes down. I filled in the open webs in the extension wings with plywood some time ago which I highly recommend as those are really annoying. You'll get a look at how they are attached later on. Front view showing the angled bottom box I added underneath (which again I would highly recommend not doing, attach directly to the legs instead if you keep the stand and save yourself two days of crawling under the saw and cursing) Filled in under the table and around the lock handle. This is in two parts because the front of the saw has just a slight curve to it and the magnets wouldn't hold with it in one piece. You can see the attachment of the web filling pieces here, there are blocks glued to the underside of the plywwod that are a little thinner than the cast iron and then just scraps of wood screwed into those blocks that pull it tight. The cover for the height adjustment slot is just attached to the screw holding the angle gauge and tucked under the angle pointer which is tight enough to hold it. At the left side at the bottom is my access to get in with a vacuum to clean it out periodically. I figured without being able to hook up the dust collector I had no chance of keeping it from filling up so I just directed all of the vacuum to the port. Cleaning it out when I choose from one spot is a lot better than having it pile up all underneath. You can also see a bit of the diagonal brace I added which made the base very solid. I should have done that years ago. Trap door open. I added a few magnets so it stays up against the bottom rail. I would have liked a bigger opening but I had to go under that rail, and I had to slope it to the left since that's really the only place where I have easy access. Back view. I just stuck a short length of pipe leftover from my 2-1/2" collection piping into a hole in the access panel. Hopefully I won't be needing to get in there. I have left the back of the saw open for now and I'll see how that goes. Quote
Andrew Pritchard Posted May 28, 2013 Author Report Posted May 28, 2013 Do any of you TS3650 owners still use the original insert plate? I started making my own wooden zero clearance inserts, and I never looked back! The only reason I still keep mine is so I can make more zero clearance inserts. Quote
Alan Bienlein Posted May 28, 2013 Report Posted May 28, 2013 Do any of you TS3650 owners still use the original insert plate? I started making my own wooden zero clearance inserts, and I never looked back! The only reason I still keep mine is so I can make more zero clearance inserts. I still use my original throat plate. I have made a total of 2 so called zero clearance inserts for my saw since I got it in 2005. One for the dado set and I only use that one for dado's that are wider than 3/8" otherwise I use the stock metal insert. The other one for regular saw blades I only use if I'm ripping something thats narrow enought to fit between the blade and the opening of the metal insert. Never ever saw a need for all these different inserts for different blades and widths of dados. Quote
Andrew Pritchard Posted May 28, 2013 Author Report Posted May 28, 2013 I've got I think 3 ZCIs - the fine cut tooth saw blade, the general purpose cut tooth saw (as the kerf on then is slightly different) and a dado. I'm going to make another dado for narrower width cuts, but we'll see Quote
rodger. Posted May 28, 2013 Report Posted May 28, 2013 I've got 6 inserts, and a few spares. I keep the original for the occasional rough bevel cut, and as a template for making additional ZCIs. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.