Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Staining

Featured Replies

I am a retired rough carpenter (framing, steel framing. drywall, etc). Finishing is not my forte. I have just finished my largest project. A 3 box 6'-6" x 7'-0" display case. I just finished staining it. Oak sub-strut with English Oak stain. The instructions on the stain can say to not let the stain set for more then 3 minutes. I am in Las Vegas, NV where it is 800 degrees out. After applying stain to one 16" x 7'-0" side the stain started to dry before I had a chance to wipe it down. Now I have a blotchy stain job. Instructions say not to sand between coats.

1. Why not sand?

2. How do I even out my finish?

 

Welcome to the forum Red!

 

Did you use any blotch control prior to staining?

What kind of stain did you use?

Can you post a pic so the way smarter people than I can see?

  • Author

Blotch control? I guess no.

The stain is MInwax water based wood stain, clear tint base.

Can't get a picture yet. I got some meat on the grill.

==> Can't get a picture yet. I got some meat on the grill.

 

Well, at least you've got your priorities in order....

 

 

The issue with oak is that the pores are deep and the stain get's down in there -- hard to get out without a lot of sanding...  I take it that's not in the cards...

 

I've no experience with WB-Minwax, so I don't know if it's a dye, stain or combo product...  Some folks lighten blotched areas using wood bleach -- is that an option for you?  I took a class with CN and came across a household product called Krud Kutter that he's enamored with at the moment and also works well (it's less stringent than a wood bleach)...  Once you start-down the chemical processes you are basically committed, so i'd practice on a deliberately-blotched cut-off from the same stock.  Also, you need to neutralize any bleach after your're done....

 

As a side note, most folks spray WB, alcohol-based, NGR, etc stains/dyes because of the overly-rapid dry times and to control the amount of dye/stain applied to the surface.

I'll look forward to a picture; but going for now on what the OP has given us:

 

I've never known blotching to be an issue in oak.  When I hear "blotch", I think diffuse porous woods with variable densities:  Cherry is the most notorious...alder and poplar aren't far behind.  The problem with a ring porous wood such as oak or ash is that the wide open pores guzzle stain while the pigment just bounces off the non-porous parts.  The result is a cartoonish exaggeration of the grain.  Sanding won't help you here.  (If anything, it'll make it worse because you'll only remove what little pigment did manage to cling to the surface on the non-porous parts.)  Moreover, blotching has nothing to do with how fast you apply the stain or whether or not you get around to wiping it in time.  If there's a patch of cherry that wants to blotch, it'll do it the moment the brush hits the board.

 

As others have said, let's see some pictures and go from there.

==> I've never known blotching to be an issue in oak.

Yea, the oaks don’t blotch, per say.  But there’s at least a half dozen reasons for uneven absorption in the oaks – especially with WB and alcohol dyes… sap wood, uneven surface prep, uneven application, etc…  Given the OP mentions high-heat and a WB colorant, I'm betting on spot-drying during application...

 

==> wide open pores guzzle stain while the pigment just bounces off the non-porous parts.  

Yea, I'm making an assumption (and maybe I shouldn't be),that the OP knows the difference between exaggerated grain and blotch, but you're spot-on, a picture is worth a thousand words…

 

==> The result is a cartoonish exaggeration of the grain.

that's a great way to describe the phenomenon...

  • Author

Hi guys, thanks for the info. Maybe blotching is the wrong description. As I said I am in Las Vegas, NV where it is in excess of 100 degrees during the day. What happened is that the stain dried before I had a chance to wipe it off. So I had blotches of dried stain. I called Minwax and talked to a rep there. Hey when in doubt go to the source. He suggested that I rub the areas with mineral spirits of paint thinner. And to make sure that it was NOT low oder or odorless. It took a few hours of extra work but it did the job. I will post pictures when the project is done. Who wants to advertise their failure! Ahh pride, what a bitch.

==> Water base stains dry quickly in normally climates.  In your climate they are probably imposssible to wipe on. 

+1

 

 

 

==> What happened is that the stain dried before I had a chance to wipe it off. So I had blotches of dried stain. 

 

OK, that makes sense and would leave you with uneven absorption...

 

 

Because it's oak, you would have to remove quite a bit of material if you went with sanding...  I would give the chemical fix a try on some scrap and see how it goes...

  • Author

I have now learned that I in my climate, at this time of year, it is better to apply the stain and wipe it off right away as I go along. Better to have multiple coats than to have it dry up on you.

==> it is better to apply the stain and wipe it off right away as I go along. Better to have multiple coats than to have it dry up on you.multiple

 

exactly -- and not just in your climate...  

==> Most major manufacturers make a retarder just for us older folks that dont move very fast anymore.  :)

 

Think it's called HVLP...

==> Most major manufacturers make a retarder just for us older folks that dont move very fast anymore.  :)

 

Think it's called HVLP...

 

For those that dont spray Butyl Carbitol, GF extender and a host of others that easily add working time.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.