Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

BLO under water borne topcoat

Featured Replies

I want to give a bit of character to a walnut frame I have made, before spraying on a few coats of water borne poly. How many days should the BLO cure before top coating?

Days? Weeks maybe? Make samples just to be sure. You want the oils to be completely polymerized before you use a water bourne.

Or try a trick I learned from Tage Frid, mix shellac cut 50% with Danish oil( like Watco) and wipe on a coat until it starts to get just a little bit stiff or sticky, then smooth out the surface with a rag and a few drops of alcohol like they do when French polishing. Let that dry 24 hours and it should be cured enough for thin coats of waterbourne . He called it 4F....Frid's fast F ing finish! He was a colorful guy.

Oh yea, forgot to mention put the finish in a container with a tight lid and shake the hell out of it before dipping your rag in to wipe it on.

GF-Seal-a-cell-clear-250px.jpg

 

Probably a bit off topic.....try some of this next time. Achieve the same goal, just takes less time than BLO. Typically dries in a day or two depending on your shop conditions.

 

As to the BLO dry.....at least 2 weeks.

 

-Ace-

  • Author

GF-Seal-a-cell-clear-250px.jpg

 

Probably a bit off topic.....try some of this next time. Achieve the same goal, just takes less time than BLO. Typically dries in a day or two depending on your shop conditions.

 

As to the BLO dry.....at least 2 weeks.

 

-Ace-

It it's compatible with the water borne?

I personally have never been a fan of BLO and a long time ago did test boards that proves it "muddies" the grain. When I use Waterlox as a topcoat I usually use orange/garnet shellac to warm it up, especially with air-dried walnut. Now that I've been experimenting with waterbornes and test boards, I've done some using WD Lockwood #98 American Walnut dye before using waterborne topcoats. I've mixed it 1:16, 1:8, and 1:4 and all look great at warming it up but still leaving the character of walnut. I actually think it looks better than my oil finishes on walnut.

I've been using a similar concept to WW's Frid application for many years under waterbourne finishes...    It goes like this:

 

Equal parts:  Zinsser Seal Coat / BLO / Real pine turpentine (NOT mineral spirits or paint thinner)      Mix it in a squeeze bottle, and keep shaking as you liberally wipe it on, wait a minute or two, and wipe it off.   Wipe again 20-30 minutes later.   Treat all rags as the extreme BLO self-igniting  fire hazard that they are...

 

The shellac seals and pops, the oil adds some color and more pop, and the turpentine is compatible with both other products and evaporates quickly.   If you can wipe it later with a dry paper towel and nothing comes off, you're ready to go.  I've applied this in the morning, and sprayed it with Ultrastar or General Finishes water based products 4-6 hours later.

 

This mix is super fast drying, easy to handle, and also eliminates most grain raising from the water based products.   The oil will amber a bit more in time, adding to the warming effect.    Darker woods and darker looks in oaks can often benefit from a bit of Trans-Tint Honey Amber in the WB clear coats.  I usually start with one drop / 8oz, and work up on a test panel.

 

Before this treatment, I'll usually sand open pored woods to 180, closed to 220, apply this mix, let dry, apply the first coat of finish, and denib / scuff with 400.   Apply additional clear coats as wanted.

It it's compatible with the water borne?

After the oil has dried. Your fine, rock on with your waterbased topcoat.

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.