PeteJr Posted October 23, 2013 Report Posted October 23, 2013 My vote is for machined pulleys and the link belt. 1 Quote
chopnhack Posted October 23, 2013 Author Report Posted October 23, 2013 Thanks Pete, that is what I am leaning towards right now. I have an email out to one supplier. I am a little concerned because my motor arbor size is slightly larger than what he had listed on his website. I am waiting on his response before I proceed. Quote
tim0625 Posted October 31, 2013 Report Posted October 31, 2013 Kick around on this site long enough and you hear some of the same things. For this problem, Steve will often point people toward the bearings and run out. That's because he's right! On older saws that have wear, bearings are often the problem and they're not a hard or expensive fix. Causes of loss of power and vibration are two different subjects. They can be interrelated but assuming there are no blade problems, vibration is basically caused by bearing wear, belt inaccuracies, or pulley defects. Any of these detract power but to cure vibration, go to these first and go to the easiest first - bearing check. If they're tight, try a link belt. If vibration persists, it may be a casting or balance problem with the pulley or it could be slightly eccentric. 1 Quote
chopnhack Posted October 31, 2013 Author Report Posted October 31, 2013 Kick around on this site long enough and you hear some of the same things. For this problem, Steve will often point people toward the bearings and run out. That's because he's right! On older saws that have wear, bearings are often the problem and they're not a hard or expensive fix. Causes of loss of power and vibration are two different subjects. They can be interrelated but assuming there are no blade problems, vibration is basically caused by bearing wear, belt inaccuracies, or pulley defects. Any of these detract power but to cure vibration, go to these first and go to the easiest first - bearing check. If they're tight, try a link belt. If vibration persists, it may be a casting or balance problem with the pulley or it could be slightly eccentric. Thanks Tim. Based on the fact that the runout of the bearing/inner flange was less than a thou. I ordered the pulleys and belt. I received them, but have not opened them yet as I have another two projects going! As I get a little closer and cleaner in the shop, I will give a full review. Thanks for the info. I really hope that this cures the issue, and I really think it will, since most of the vibration comes from the motor bouncing on the belt when running and yes that does come from the motor resting on the belt and creating a flat or the overlapping of the cords in the belt, I am not sure which. When I am finished, I may devise a system to store the saw with the weight of the saw taken up off of the belt... Quote
tim0625 Posted November 1, 2013 Report Posted November 1, 2013 On the craftsman that I used to use It was a simple matter just to lift the weight of the motor up and take the belt Off of the pulley when I was not using it.... Quote
chopnhack Posted November 2, 2013 Author Report Posted November 2, 2013 On the craftsman that I used to use It was a simple matter just to lift the weight of the motor up and take the belt Off of the pulley when I was not using it.... After swapping out the pulleys and belts yesterday I completely understand what you are saying. I wasn't sure as this is my first contractor saw. I wonder if I should store the link belt in the same fashion? First report, awesome!!! I really must make a video or something, day and night.. Quote
PeteJr Posted November 3, 2013 Report Posted November 3, 2013 Next you may consider Contractor Saw PALS by In-Line industries. http://in-lineindustries.com/products/contractor-saw-pals/ 1 Quote
tim0625 Posted November 3, 2013 Report Posted November 3, 2013 Good deal! The link belt won't be as prone to develop memory like a regular V belt but if it's a simple thing to remove it from over your pulley, do it and just make it a part of your start up when you go in the shop. Wow...it's 46 degrees this morning in coastal SC and feels great!! 1 Quote
chopnhack Posted November 4, 2013 Author Report Posted November 4, 2013 Next you may consider Contractor Saw PALS by In-Line industries. http://in-lineindustries.com/products/contractor-saw-pals/ Bro, now you tell me! Trying to save on shipping here :-P Just kidding, I did the 5 cut test when I first bought the saw and found it to be accurate. Probably a good thing to repeat though. Thanks for the thought. Quote
chopnhack Posted November 4, 2013 Author Report Posted November 4, 2013 Good deal! The link belt won't be as prone to develop memory like a regular V belt but if it's a simple thing to remove it from over your pulley, do it and just make it a part of your start up when you go in the shop. Wow...it's 46 degrees this morning in coastal SC and feels great!! Yes, I am loving the cooler temps here too.. high of 86 the other day :-P Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.