Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Question for Graham

Featured Replies

I repaired some sash made in mid to late 1700s that were made from a wood that I don't quite recognize. It looks very similar to what is called Heart Pine here-from the Long Leaf pine tree, but it has much more soft grain relative to the hard grain-maybe 4or5 to 1.  It's much softer than our Heart Pine, and works almost like White Pine but is some bit harder.  Color of the soft grain is more brown, and hard grain is not as dark as our Heart Pine.

 

I was thinking there is a good possibility that the sash were imported, and maybe from England.  I searched online, but no luck with any info.  I was wondering if you had come across anything like this over there, or maybe knew someone to ask.

 

The house was built in 1784, so sash were probably made within a few years before that.

 

Thanks,

I'm a Graham so I'll go first  :).

 

Tom, my guess would be pinus sylvestris more commonly know here as European Redwood and also known as Scots Pine, Red Deal, Baltic Redwood, Archangel Pine etc. To contrast it with North American timbers that I have used I would say it's close to SYP but with more knots and ER is considered to be moderately durable whereas SYP is rated here as perishable (and I can confirm that to be the case)

 

The oldest windows I have worked on were window from this place. If you scroll down you can see other aspects that were used in our town hall (image below)

 

South%20Molton%2010.jpg

 

These are perhaps some of the most early types of sashes. Sashes are about 32mm thick and glazing bars are the same thickens as the top rail and stiles at around 44mm. Heavy glazing bars like this are usually indicators of early designs before those ultra fine 15mm bars kicked in during the Georgian Period. They did not have pockets so I assume they were corded before fitting. The pine in these was a bit more rough and ready than the mainly plantation stuff of today but I would still hazard a guess that they were made from ER.

 

Got any picks of your?

  • Author

That wood sounds like a good possibility.  I didn't take any close ups of the wood itself, but here's one of the old sash that we replaced a couple of mullions (long glazing bars) on.  1-1/16 thick.  Single hung, meeting/lock rails same thickness as the rest of the sash.  These were typical of houses here from mid 1700s to early 1800s.  It looks to me like the jambs were made here-4x7s with stops carved into them, and the sash came from somewhere else.  I'll try to get a better sample of the wood by itself another day.

 

I'll learn to spell your name correctly one day.  I'm doing good to remember what it is.

post-14184-0-19467800-1380311934_thumb.j

  • Author

The repair of that sash was easy.  We decided not to put the new sash in the house, since they are so nice and work is really just starting on the house.  We found enough pieces of the 36 old windows to put together enough donor parts with some new parts to get 12 complete sash, so we can have daylight in every room.  The new parts for the reproduction sash interchange with the old sash perfectly.  We just ran two new mullions with the setup we have for the new windows, and stuck that sash together.

 

I've changed the design of the mullion to muntin joint for the new ones, but for these I just punched the big mortises all the way through like the originals, so the old muntins would fit.  I didn't worry about getting the fit good.  That's just the way it went back together without fiddling with it.

 

One really cool thing about these sash, new or old, is that you can knock the pegs out, take it apart, and replace parts.

  • Author

I'm changing the design of the mullion to muntin joint.  Almost all the old ones broke because most of the wood was taken by the mortise.  This one was done quickly by hand on the new piece.  I have another small mortising machine on order to cut the 168 of these joints that we have to run, so I can leave the one I have set up for the 3/8" mortises.

 

I don't know if you can tell anything by these old painted pieces about the wood or not.

post-14184-0-55382500-1380313362_thumb.j

Yep, looks woody alright  ;). Hard to tell Tom but your Heart Pine looks a real close match to the wood in those windows. I joint that is nice and strong there is a mitered cross halving, that said I think I have done that only once or twice. With a single end tenoner with scribing heads at hand we normally run a stub tenon like your doing there. 

I assume the vertical glazing bar/muntin runs top to bottom as these are vertical sliders? Also on the pining I'm yet to find a sash that will let me do that. Early stuff I find is nearly always wedged with a pin in there sometimes with late stuff sometimes being held with an aluminium star dowel. Ever used them before? They really test the hammer skills.

  • Author

Aluminum star dowel is foreign to me. 

 

Yes, single hung vertical sliders.  The stops are carved into the 4x7 jambs.  The lower sash only, with stops on the head, hold the upper sash in.  The lower sash slides by the upper with direct contact, and no tapered meeting rail.  The upper and lower sashes slide against each other.  Other houses around here up until the mid 1800s have windows built the identical same way.

 

Yes, the vertical bar runs top rail to bottom rail, and is pegged in both places. The upper tenon on the mullion is through the meeting rail.  Short horizontal muntins just sit with their tenons in their mortises.  The large mortises in the mullions were fatal to the majority of them.  Interesting that fast and cheap were priorities back then too.

 

Mitered cross halving would be too different, and too modern to satisfy the purists.

 

These are all pegged. The 230 year old ones come apart about like one of the new ones that I just put together would.

 

 It was an interesting study in draw boring peg holes.  The old ones were draw bored, and a good majority of those joints failed because of it.  All the holes were elongated in the tenons.  Some tenons that had completely vertical quarter-sawn grain had the whole section down-strain from the peg popped loose, and was fatal to that joint.  I don't think I will draw bore anything with these dimensions.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.