Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Best satin finish for pine farmhouse table

Featured Replies

I built a farmhouse table from pine 2x6 boards.  I found an English Chestnut MInwax stain that I like.  I tried sealing the stain with Minwax satin wipeon poly.  It seems to be a little to shiny for my taste.  Can you suggest something that will look a little less shiny and still protect the wood from water spots and other damage?

 

Thanks,

Judy

The first thing would be to be sure you stirred it really well.  With the semi-gloss and satin polys the flatteners often sink to the bottom of the can.  

 

Also I've found the first coat or two won't have the expected sheen.  Try a sample board with a couple more coats (well stirred) and see if it gets better.

If a 30 degree sheen (satin) is too high for you you either didn't stir the can or look for a flat finish which is about 10 degrees.

==> Also I've found the first coat or two won't have the expected sheen. 

 

You can purchase flatner...  just make-up some sample boards and keep adding until you get the finish you want...  1 QT of flatner will last you a lifetime...

 

Since you're using a poly, here's one that would work for you:

 

http://www.jamestowndistributors.com/userportal/show_product.do?pid=135&familyName=Interlux+-+Flattening+Agent+for+One-Part+Finishes

  • Author

I think my problem is the way I am applying the wipe on poly.  I am unhappy with my results and I am going to sand it back to bare wood and start over.  I found these directions from Franklin Pug in another post.  I think I will try this on a sample board.  My only question is ... should I raise the grain with water and sand it down before I apply the stain?

-----------------

1. Choose nice boards. No finish can make an okay board look fantastic. Take your time and choose your face stock carefully.
2. Sand, and vacuum.
3. Raise the grain by wiping down the project with water. Let dry.
4. Another light sanding and vacuuming
5. Flood wipe only poly on the surface of your project using a disposable foam brush. Keep applying until the wood will not "drink" anymore. Wipe off excess with a clean rag and let dry overnight.
6. Apply a second coat of wipe on poly with a rag, and wet sand (by hand) using 400 grit wet/dry sandpaper. Wipe off excess. Let dry overnight.
7. Apply a very thin coat of wipe on poly with a rag in the direction of the grain. Do not wipe off, let dry for about 2 hours. High humidity could extend this time
8. Repeat step 7 a few times. I usually do 4 or 5 of these thin coats.
9. Let cure for 4 days or so.
10. Apply paste wax with 0000 steel wool and let dry for a few mins (hazes over). Wipe off with more clean rags.

The steel wool helps get rid of any dust nibs that get in your finish.

You can also let a new can of satin finish settle and decant off some of the finish.   This will increase the ratio of flattener to finish.

 

Carefully pour or scoop off 1/2 of the liquid from a new can of satin before stirring.   Stir the remainder and apply to a test board.  If too flat, add 25-33% of the decanted finish back in, stir, and test again.  If still too shiny, remove more liquid from a settled can.

 

Save the gloss stuff you decanted, as it's good for early sealer coats.  Sealer coats work well if glossy, as it helps you see where you scuff sanded.

Just because you asked for other suggestions for products, I've used Arm-r-seal Satin on many woods (including pine) and I have never regretted it.  It's super easy to apply and you practically can't mess it up. 

 

That being said, all the other suggestions should help you out if you wish to stay with your current product and try again.  

 

 - EG

You can also let a new can of satin finish settle and decant off some of the finish.   This will increase the ratio of flattener to finish.

 

Carefully pour or scoop off 1/2 of the liquid from a new can of satin before stirring.   Stir the remainder and apply to a test board.  If too flat, add 25-33% of the decanted finish back in, stir, and test again.  If still too shiny, remove more liquid from a settled can.

 

Save the gloss stuff you decanted, as it's good for early sealer coats.  Sealer coats work well if glossy, as it helps you see where you scuff sanded.

Great tip. I have been mixing GF Endurovar flat and satin for the same purpose.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.