Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

A simple modern bookshelf made from 1/2" baltic birch plywood

Featured Replies

Hi all, 
 
newbie woodworker here with my third attempt (first was a cross cut sled, second an outfeed table) in wood working. Have not done anything for a long time, I think almost 25 years. As a student I made a closet and a platform bed as well as a very simple book shelf  for my small apartment, in my father's workshop. No meaningful  projects since then.  Many of you will probably not count this as real wood working and you are probably right. It is more of a skill building activity with one of the three wood working tools I have (table saw, miter saw and handheld router).  Something like "learn how to make exact cuts on your table saw".
 
However, after moving in our new house we were looking for a bookshelf but none of the stuff we could find was really what we wanted. Don't get me wrong, there are wonderful book shelfs on the market but the price is often not so wonderful. Long story short, I decided to build one myself. For already a long time my modern book shelf favorite was the FNP book shelf, which has been designed back in 1989 by Alex Kufus in Germany. The concept is just as simple as genius.  The side panels holding rectangle aluminum rails, while the shelf boards resting on these rails and holding them in place. This results in a very sturdy construction, while a lot of variations in the shelf bay are possible.
 
As is said, the idea for this shelf is borrowed from here: 
 
and because I already owned one of those years ago I knew the concept and got the measurements from the website and the catalogues.
 
First I made a sketch and three dimensional drawing in SolidWorks (overkill for such a simple structure..).
 
post-14659-0-97573300-1383476323_thumb.j  post-14659-0-51690400-1383476333_thumb.jpost-14659-0-21771100-1383476341_thumb.j
 
I played a little bit around with the measurements, but finally decided to stick with the original size. Thus what you can see on the picture is almost 8 feet high.
Looking at these pictures, my biggest fear was not be precise enough while cutting the pieces. 
 
post-14659-0-91149700-1383477787_thumb.j
 
If the mortises in the shelf board are not exactly parallel, the board won't fit in place. On the other hand side they need a tight fit, because that has influence on the sturdiness of the whole structure.
 
more to come
 
 
 
 

 

Interesting construction!  I look forward to seeing how this comes together.

  • Author

Very impressed by your 3D 'drawing'. Do you work for DreamWorks???

 
I do not work for Dreamworks, unfortunately, would be cool. 
Actually this is a kind of hobby, for a long time the only way to be "creative" because I never had enough space for a real workshop until we moved in our new house. 
If you have a sense for this kind of software is actually pretty easy to make such  drawings and it needs only a little bit training.
 

We should start a thread for computer drawings. I prefer Inventor since that's what I learned on. 

  • Author

Although four of the pictures showing the shelf in normal wood colors, my plan was to make it from 1/2" phenolic faced plywood. By using this material it gets a very  resistant surface and no painting would be necessary. In addition, together with the aluminum rails it will have a nice appearance.
However, phenolic faced plywood is really hard to get. No chance from any local dealer in my area. Asking my local dealer for this stuff  he told me that he can't even order it from his supplier. Finally I found some places where you can get black phenolic faced plywood, WhiteCap (Baltimore) and Boulter Plywood (Boston) - there maybe more places, but a lot of them don't even talk to you if you are not a company - but this stuff is expensive and shipping cost makes it even worst. Thus I decided to make a test version from 12" baltic birch plywood and because I could only get 5' X 5' sheets, the shelf will be a little smaller.

I started with cutting the side panels,  cutting unequal pieces was my biggest concern, so I checked my table saw settings twice and every piece after the cut.
Finally I ended up with a nice pile from plywood panels of equal width. Not very exciting...

post-14659-0-10162800-1383680707_thumb.j

post-14659-0-98417200-1383680711_thumb.j

  • Author
I did enlarge my crosscut sled with some plywood stripe and supported it with a work roller. I put my outfeed table aside from my table saw and adjusted the hight so that the work roller just touched the table surface. With that setup I was able to cut the side panels to equal length. Then I did some test cut to figure out how deep the mortise for the aluminum rail has to be and started cutting them. 
This time I ended up with a pile of  side panels with equal width, lenght and mortises with exact the same size and position. I put two pieces of  aluminum rail in the upper and lower mortises and this time was a kind of excited that everything came nicely together.

post-14659-0-61337300-1383697671_thumb.j

post-14659-0-89835000-1383697683_thumb.j

post-14659-0-37003600-1383697731_thumb.j

post-14659-0-03541100-1383697732_thumb.j

  • Author
OK, let's continue with this little project.
 
On my way to finish the side panels I realized the outer panels need holes right above the mortise. These holes are corresponding with holes in the aluminum rail and a flat head solid rivet goes in there to prevent the rail from slipping out the mortise.
 
post-14659-0-01662900-1384089391_thumb.j
 
post-14659-0-31245200-1384089392_thumb.j
 
Because I do not have a drill press with the capacity to bore holes into the front side of the panels, I decided to make a drill jig. 
 
OK I should probaly mark this off topic..... ;)
 
 
Cutting a piece of aluminum with the appropriate width (miter saw with non ferrous metal saw blade - works perfect  [ youtube.com/watch?v=ZC6d3k2OM9U ] ), milling to size and boring the hole. And  there is the finished piece. Making some test holes in a scrap piece of plywood.
 
post-14659-0-49204400-1384089394_thumb.j
 
post-14659-0-32869700-1384089396_thumb.j
 
post-14659-0-57972800-1384089397_thumb.j
 
post-14659-0-77827900-1384089398_thumb.j
 
Finally I cut the shelfs boards, 20 in number, with the sled. Unfortunately I did not realized that making the sled I  made some mistakes. Thus the sled had almost 0.08" play, with the result that the boards had not 100% the same size.  :(
 
post-14659-0-46924100-1384089400_thumb.j
  • 4 weeks later...
  • Author
It is almost a month since I posted something about my little project, unfortunately to much other stuff was going on.
OK, let's continue some, as you know from my last post, the boards were not exactly the same size, better they were no exactly square. That happened, doing the cross cut's with a sled, that had to much clearance in the miter slot.
I adjusted my sled and then decided to cut 1/16 from the front and trailing edge of each  board, to get boards of  equal length.
With the sled fixed it turned out nicely.
 
post-14659-0-10764500-1386199004_thumb.j
 
Now I could move to the next step, cutting the mortises in the bottom side of the  boards where the aluminum rail will fit in. This was not a big deal while the kerf of the saw blade has almost the same size like the aluminum rail. Testing this with a piece of aluminum rail it was a nice tight fit. However, when I assembled the pieces I realized that this was to tight. I enlarged the mortises by 1/32" by putting a feeler gauge in between the board and the fence and then cutting the mortise again.
 
 
post-14659-0-38451200-1386199113_thumb.j
 
Now it had still a good fit and I was finally able to start with the assembly.
You can see here how the front and the back rail gets attached,then the boards simply sit on the rails. 
 
post-14659-0-59520300-1386199206_thumb.j
 
Time to use my drill jig, which was really handy to get the holes in the exact position.
 
post-14659-0-58038000-1386199510_thumb.j
 
The rail is flush with the board and a rivet holds the rail in place.
 
post-14659-0-18977500-1386199694_thumb.j
 
Getting the hole in the right spot so that the rail and the board are flush and the rivet fits into the hole I think that would not  been possible without  the drill jig.
 
 

Looking good, Christopher. I like the design and your attention to detail. That attention will go a long way in making you a better woodworker. Thanks for posting the pictures.

  • Author
@Troy
thanks for your positive comment, sometimes that helps to finish a project.
 
Finally I was able to assemble the whole thing.
 
post-14659-0-82958700-1386288970_thumb.j
 
post-14659-0-61257400-1386288977_thumb.j
 
post-14659-0-46934700-1386288984_thumb.j
 
I did that to make sure that everything fits in place. I also changed the position of some of the boards to see whether they fit in any random postition or not. They did, so time to disassemble and work on the finish. If I would have used phenolic laminated plywood then there would be only little to do to finish this job.  But I have not, so the whole thing needs some kind of surface treatment. 
I sprayed every piece with some water to raise the grain and after the boards were dry I started with sanding 80 -120 -180 -220, which was a pain. 26 boards have 52 surfaces... now I know why people designed them from plywood with already finished surfaces.
 
post-14659-0-07618400-1386289344_thumb.j
 
Then finally my new router table extension on my table saw could be used. I chamfered the front and the rear edges of every board because they were very sharp. A total of 104 chamfers had to be made, I was really happy to do that on a router table instead with an hand held router.
 
post-14659-0-70600300-1386289361_thumb.j
 
post-14659-0-72495000-1386289710_thumb.j
 
In the meanwhile my wife picked a color and I decided to use a waterbased dye. The picture shows a test board, waterbased dye, color is amber from General Finishes, sprayed, with 2 layers top coat.
 
post-14659-0-38005800-1386290211_thumb.j
  • Author

OK...

After hours of painting then sanding  and more painting and more sanding it is finally done. "NO I would not recommend this to a friend"  ;)  It was a real pain, even though I used an HVLP spray system for the finish. Considering the season painting outside was not really an option, so I prepared a little space in the basement and tried to provide adequate ventilation. All doors and windows open and additionally a fan in the egress window, which believe it or not, helped a lot with ventilation. However, a respirator is mandatory anyhow.

 

post-14659-0-96576000-1386699991_thumb.j

 

post-14659-0-22708100-1386700011_thumb.j

After enough dry time things could finally evolve from the basement into the living room.
I think it has a lot of flaws.... anyway, it is my first piece of furniture since almost 25 years, and back then as a student "finish" wasn't very high on the list :rolleyes: . So this time it is much better but still far away from perfect, although most of the big flaws are not so easy to see once the pieces were assembled.

My wife likes it, therefore I think "mission accomplished"

 

post-14659-0-79762200-1386699905_thumb.j

 

post-14659-0-82078900-1386699921_thumb.j

 

post-14659-0-24150800-1386699944_thumb.j

 

post-14659-0-94157200-1386699961_thumb.j

 

post-14659-0-97367100-1386699973_thumb.j

 

 

Looks pretty frickin sweet. If I didn't know to look I wouldn't have realized it's made from plywood. How many hours would you say the finishing process took?

  • Author

Looks pretty frickin sweet. ....

 

 

Thanks!

 

I think I can answer your question relatively precise because at some point sanding and painting was so boring that I started to time how long I needed for one piece. 
So it was something like 2 minutes each sanding the small pieces. 4 minutes each sanding the big pieces.  This adds up to approx. 8 h of sanding, 4 hours  before I started color spraying,  and approx. 4 h between color and top coat layers. I needed approx 1h to spray all parts, I did five layers, which adds up to approx. 5 h. Let's add approx. 3 h for setting up the work space and cleaning tools, so we end up with around 16 h only for the finish... more than double the time I needed to cut all the parts. 

Very nicely done. Though many don't like plywood much, I think Baltic Birch ply can give impressive results - as you have demonstrated. Matches its environment well too.

 

John

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.