Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Problem with polyturethane in pores?

Featured Replies

I had a table that was finished with polyurethane that needed some TLC (lots of scratches, etc.). I stripped it with Citristrip, scraped it, sanded it through all of the grits, and then sprayed a Transtint + Minwax Polycrylic finish on it. I was very frustrated to see the result (attached) had strange color voids around many of the pores. The table was a white-ish wood and I sprayed a brown dye mixture, so you can see all of the white spots remaining. My first thought is that there is still some polyurethane down in the pores and the Polycrylic is "polyurethane-phobic" and thus doesn't stick/soak into wdeeper pores that might still have some polyeurethane in them. If so, I think my options are:

 

1) strip it again (ahhhhhhh) and this time use a brass brush to scrape the old finish out of the pores

2) strip it again (ahhhhhhh), spray a coat of shellac (which should stick fine to both the polyurethan on the bottom and to the Polycrylic on the top), then spray my dye+Polycrylic

 

Am I right about the problem? Are those my only options from here? Any suggestions that don't involve stripping it again?

 

Thanks!

David

post-13877-0-84125400-1388875484_thumb.j

Looks like fisheye. Shellac is the only thing on Gods green earth that can fix it. Strip it sand it spit coat seal it then see if the stain behaves. More shellac if not.

Silicon is the problem. It's in lots of furniture polishes.

Steve

Get a hotter stripper that contains MC. You need to to get down into the grain removing old finish with a brass brush and scrub that wood. When done, wash the wood off good with mineral spirits. Let the project dry for a few days. Then come back with 50/50 water and denatured alcohol and wash the wood due to using a water-based toned topcoat.

 

When the wood is dry, sand your wood. Clean off the dust then apply your toned water-based topcoat.

 

You may want to consider skipping the toned topcoat and dye the wood directly for your color. Then apply your topcoat. If your not proficient at spraying toned topcoats, they can get tricky. Plus this being a tabletop. Any chips to the surface of your table, your removing color showing the white wood underneath.  

 

-Ace-

Ace,

Are you saying that fisheye causing silicon contamination can be stripped, sanded, and washed off? Short of sanding 1/8" off I'm not sure it will work in my experience. I've driven myself nuts trying to overcome it without using shellac.

Steve

Ace,

Are you saying that fisheye causing silicon contamination can be stripped, sanded, and washed off? Short of sanding 1/8" off I'm not sure it will work in my experience. I've driven myself nuts trying to overcome it without using shellac.

Steve

 

Yes I am saying that.  :)

 

Done it forever. The build up is in the deep grain and most folks forget that fact. You lift the surface, off comes the contamination. That's why we wash the wood down afterwards to make sure. If your getting contamination of a finish after stripping. You didn't completely "strip" the finish. A good strip job means your back to white wood. Hardly any color should be left behind and the grain cleaned out as well.

 

-Ace- 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.