Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Delta dust collection suction capacity

Featured Replies

Hi all,

 

I am new woodworker and novice forum poster looking for some DC advice. I have a Delta DC unit that is 1100 or maybe 1200 CFM suction. I want to make a run of pipe that travels to a 9' ceiling then ~20' across and back to down ~6' feet to my planer, jointer, and miter station.

 

I will be running just one tool at a time so all of my proposed blast gates for the other tools will remain closed. 

 

Do you think the DC has enough suction to accommodate my needs? I have a standard 20x20 2 care garage that I am turning into the run of the mill amateur wood butchers shop.

 

I appreciate any insight you all have. Please let me know your experience and thoughts.

 

-Kendall

Generally, it's not advised to try to duct a 1.5 hp DC unit.  However, smooth wall duct/pipe has less resistance than flex hose.  So it would be better to have say 10 feet of pipe and 2 feet of flex hose than 10 feet of flex hose.  What I did was put my 1.5 hp DC in a corner and I have everything that is hooked up to it on the two walls next to it with nothing more than about 10 feet away.  I also reworked how the DC was set up so that instead of the blower being down near the floor it hangs upside down from a frame as close to the ceiling as I could get it, to get rid of the ducting that would have gone from the floor to the ceiling.  Putting your DC on the opposite end of the shop from where you want to hook things up is something you can only really get away with with a larger unit.

==>Delta DC unit

What model?

 

==>that is 1100 or maybe 1200 CFM suction

This is at fan inlet... Which may/may not be adequate for approx 600cfm at tool port...

 

==>9' ceiling then ~20' across and back to down ~6' 

You're talking 35 feet of pipe... We really need to know the model to be able to help...

 

==>planer, jointer, and miter station

Need to know inlet port size and CFM requirement of each tool.

I'll also ask, which model?

 

This topic - ducting a 1.5hp DC - seems to have 2 major schools of thought, "you can't do it" and "I did it and it works fine".

 

I am solidly in the second camp - I did it, and it works fine.  I have the 1.5HP Delta 50-760, connected to my TS, BS, jointer, and planer using 4" smooth walled irrigation pipe, blast gates and a short piece of flex at each tool, and it seems to work well.  I did a rough back-of-the-envelope calculation using the SP loss of all my pipe and elbows, against the performance curve of this particular unit, and it seemed be OK.  If I had 6" pipe available, I would have used it for my main horizontal run and the drop down to my DC, but the runs to individual tools I would have kept at 4" in order to keep the airflow high enough (for the same CFM, a larger pip == slower air movement). But I ended up with 4" pipe all around.

 

Some tips:

- Reduce the length of runs as much as you can

- Definitely eliminate as many 90* turns as possible, or use multiple 45* fittings to make a more gentle turn

- Minimize the amount of flex as much as possible - as I recall, flex has 3x the SP loss of smooth pipe of the same length (on a good day).

- Try to run the pipe all the way to the DC if possible - it's easy to use flex, sure, but with a little work you can eliminate that piece.

I'm halfway in the second camp...I did it, and it works okay.  I have a 2HP with a similar run of pipe.  I'd bet my dollars against your donuts that you'll find it does a great job pulling the big chips off the planer and jointer, and does mediocre at best pulling the fine dust from the table saw and bandsaw.  I have mine set up as efficiently as possible, and I get acceptable results.  But I'm in a garage so I don't worry about dust that much...I just want the bulk of the mess pulled away, and it does that.  I'll open the door and use my backpack blower to dedustify the shop whenever needed.  If I were in a basement shop, it would not be adequate.

Good point Eric- the proof is in the performance.  I could see in some situations the performance might not be good enough.  For me, it works well.  Collection on my TS and planer is awesome, but the TS is a Sawstop and has a nice blade shroud and generally great dust collection, and my planer is a Dewalt lunchbox that has a built-in fan.  My jointer is 'ok' but I'm not sure how to improve it. My bandsaw is so-so, but I have plans to remove the stupid plate that basically blocks the DC port, as well as make a fitted box under the table to collect more.  A respirator is always a good way to protect yourself, so please consider that as part of your DC control strategy.

Yeah, it's really one of those questions with too many variables to answer, kind of like the ol' "which tool should I buy next?" question.  It's not like working on a Rubik's cube where when it's done it's obvious that it's right and as good as it can get.  How big is the collector?  What micron filters?  Cyclone added?  What size pipe will you use?  How many feet of run?  How many turns?  How sharp are the turns?  How many blast gates and how many tools?  How well was each tool engineered with DC in mind?  How picky are you? etc, etc.

 

The best way to go about it without going whole hog and buying a big 5HP cyclone and 6" pipe, is, unfortunately, trial and error.  Get your system up and running, test it out, improve until you're at max efficiency for the machine you have.  Then upgrade when it's justified.

  • Author

Wow, thank you guys for all of the input thus far!

 

Triple, the model is the 50-850. It is an early 90's model I believe and has 2 4" inlet ports and the standard canvas bags. As far as requirements for each tool I honestly don't know right now. My planer is an early 90's Woodtek 15". I would imagine it requires 600? My jointer is an old 1940's boice crane that I am currently devising a better DC system for. It will have a 4" port as well. The miter station is currently voodoo to me. (I really just haven't had time to really tackle it) My bandsaw will be very near the DC and shouldn't be an issue. Its a 14"Jet with a 2.5" port. Lastly, my Delta contractor saw is outfitted with a subpar system that needs some engineering done to it as well. Then I've got my benchtop router table with 2.5" port and sanders with 2.5's. They're easy to deal with using the shop vac and my little cyclone separator contraption.

 

John and Eric, I am in a similar situation to you in that my shop is in my garage. I am mostly concerned with the bulk of the material being removed. I understand all of the information on shallow bends and short runs and I'm going to do my best to keep it simple. I really don't have a major problem just rolling everything to where it needs to be, but I sure as hell would like to try to give everything a home. I would imagine it would save me a fair amount of time. Shoot, maybe I'll just get a 20' flex hose and call it good. Naturally, it gets old stepping over the hoses and such all the time though.

 

Thank you guys again for your thoughts.

 

-Kendall

==>model is the 50-850
From delta, specs are: Bag Dust Collector, 1-1/2HP motor, 1200 CFM, 11.4-static water. You're going to get 1200CFM or 11.4in/H2O, but not both at the same time. It’s a bag system and going to work in your favor – you lose a bit w/ cyclone.
 
==> I am mostly concerned with the bulk of the material being removed.
You expectation is reasonable. If you are very careful in your duct layout, you should be able to capture the bulk of mid-size chips. You won’t have the CFM/lift to capture larger chips, nor the velocity to capture fines. With this setup, you should still use a dust mask.
 
Note: Flex-hose should be kept at a minimum…

CFM/lift to capture larger chips, nor the velocity to capture fines.

 

 

Dyslexia? :)

==>Dyslexia?  :)

Always type faster than I think... Keeps folks on their toes... :)  

 

As a mentor, spreading confusion is my goal... :)

 

Should have clarified velocity to minimum velocity required to move fines through the system… and CFM/H2O: sufficient airflow to overcome static pressure of either large chips or clouds of fine dust…

 

But I think you got what I meant – even if a little convoluted.. :) 

 

Point is, if he's careful, he'll collect the majority of the mid-range dust/chips, but large chips and fines won't be collected over the 35'...

  • Author

Thanks guys. I do use a respirator regularly.  I reckon I'll just give a minimalist/simple approach to it and see how it works. I've seen so many photos and videos of folks with very similar setups that appear to have excellent results so i've got high hopes.  

I have the 1.5 hp delta 50-760. It does a great job when I wheel it around, connected with a 5 foot length of flex hose (5" diameter hose). I would want larger if I were to duct it.

Kendall - my shop is actually in my basement.  I know it's not scientific, but I used the "layer of dust" metric to gauge if my DC is helping.  When I piped in my DC to my tools, I saw a drastic reduction in the layer of dust that coated everything.  Almost eliminated.  The biggest culprit for that now is my CMS, which has no dust collection....one of my next shop projects.

 

Even though it's a lot better, I still use an air cleaner (Jet AFS1000B) to clean the shop air, and I also try to use a respirator as much as possible.

 

Here's an article reviewing a number of DC units.  The 50-850 is one of them.  It was helpful to me to understand the performance of my unit as the SP loss increased.  With yours, I'd recommend looking at improving on the top bag.  5micron is not terrible but you can do a lot better - and something like a Wynn filter might give you better filtration *and* better performance.  

 

http://www.portercable.com/uploads/PCD/Documents/News/182DustCollectors.pdf

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.