Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Can you help me diagnose my table saw problem?

Featured Replies

  • Author

The curve is such that when I try to glue two boards together the ends of the boards meet, but the middles don't which is how I noticed the problem. I've not looked too closely at how even the curve is and it's more than likely effected by how long the piece is.

 

I try to be even in my pressure on the end of the board to prevent the blade from burning the wood. I've even practiced keeping the work moving so I can grab a push stick to reduce burning and prevent wearing spots (or better yet, started the cut with a push stick).

 

This is more of a gradual curve spread along the length of the cut, so I don't think slowing the cut down is the issue.

 

I might have to take a photo or to try and demonstrate the problem.

Any difference in the moisture content on the material you're working with?

I would try a different blade. It's the easiest thing to try. I usually start with the simple things first.Don't make a mountain out of a mole hill.

  • Author

Any difference in the moisture content on the material you're working with?

 

Very unlikely as most of the pieces are re-sawed from the same block of hardwood. The plywood has been out in the barn so subject to below freezing temperatures recently.

Grab a scrap square of plywood about 20" long 6" wide. Rip cut it using your fence, stop 2/3 of the way and power off, flip end for end with the saw off and run it back into the blade as if you were trying to run it backwards. If it hits the blade your fence is off.

If you have just a bow in the center of a glue line rip your saw and blade are not a good fit with each other. Meaning if your blade is dull or your saw is underpowered for the blade you will get the bowed glue line. Anytime you apply force to the stock beyond that of the saws capacity you will bow your cut. You can tell if this is the case. Rip a piece of jointed hardwood, move the fence in just a hair meaning small hair. Run the same piece back through just barely shaving the edge if it just knocks off the high ends and leaves the bowed center your saw is lacking power or a sharp blade.

  • Author

Grab a scrap square of plywood about 20" long 6" wide. Rip cut it using your fence, stop 2/3 of the way and power off, flip end for end with the saw off and run it back into the blade as if you were trying to run it backwards. If it hits the blade your fence is off.

If you have just a bow in the center of a glue line rip your saw and blade are not a good fit with each other. Meaning if your blade is dull or your saw is underpowered for the blade you will get the bowed glue line. Anytime you apply force to the stock beyond that of the saws capacity you will bow your cut. You can tell if this is the case. Rip a piece of jointed hardwood, move the fence in just a hair meaning small hair. Run the same piece back through just barely shaving the edge if it just knocks off the high ends and leaves the bowed center your saw is lacking power or a sharp blade.

 

Next time I'm in the barn winter workshop, I'll check this out. It could be that the blade is dull, I've not ruled that out.

Any chance the fence is slipping on the rail slightly during a cut?

 

At the very least, clean the blade.

  • Author

Any chance the fence is slipping on the rail slightly during a cut?

 

At the very least, clean the blade.

 

I can't say that it's not, but I don't think it's likely that the fence is slipping.

 

I certainly can't go wrong with cleaning the blade!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.