Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Anyone have the Rikon 10-325 14" bandsaw?

Featured Replies

I'm kicking around the idea of buying my wife's grandfather a new bandsaw. It has to be 110V. The Rikon seems to be a good saw that can still be wired for 110. I've also looked at a few grizzlys in a similar size and that have similar resaw capacity. Does anyone have any experience with the Rikon 14 inch? If so, how do you like it?

It's "okay." I'd put it in the same ballpark with Grizzly, maybe a little higher. Sometimes I wish I would have put out just a little more money for the Laguna or Powermatic, but the bandsaw does what I need it to do, so can't complain too much. One big complaint on mine is that the upper post moves inward and outward when you tighten and loosen the knob, so the bearings may no longer be aligned if you have to raise or lower the post and retighten. That said, I did not notice the same issue on the 10-325 in the workshop of my local Woodcraft, so it could be an issue with mine. I used some tape to better shim it and make it stay put when loose.

 

The bearings are a bit of a pain in the butt too, tightening them makes them shift ever so slightly making it a trial and error issue. I've been tempted to replace them with Carter bearings, though I've heard mixed comments here and there that they have the same issue too, so that has not won my confidence enough to put the money out yet. I've been able to get acceptable resaws out of it, but tend to fight a little drift here and there and sometimes make wedges no matter how much I adjust for it. That could have to do with my technique, as well as the blade, I've said before the Timberwolf blades haven't exactly blown me away. Ask me again after I eventually try a Woodslicer or something comparable.

 

The lamp is on the back of the unit putting the light behind your work rather than in front of the job at hand, sort of "huh?" The lamp also needs to be plugged in seperately from the bandsaw, I assume in case the unit is wired for 220v. Tension meter is worthless, but tensioning by blade is better anyway. There is a stupid safety baffle plate on the inside impeding dust collection so you don't stick your hand in, but that can be removed with a Dremel or something. Fence is "okay," better aftermarket ones to be had but I still use the stock one. Have a Carter Mag-fence, but never really got on to it.

 

Ultimately I would mildly recommend it, but only if you get it on sale, most definitely not for the full retail price. Woodcraft puts this on sale for $799 now and then, so it pays to wait.

I was able to do a side-by-side comparison of the Rikon 10-325 and the Laguna 1412 at my local woodcraft last weekend.  The Laguna 1412 is a little more expensive, but in my opinion is the higher quality saw.  Some of the things that stood out were the Laguna's much heavier trunnion and the heavier rack & pinion blade guide.  The best way to describe it was the Laguna just looked and felt like a heavier duty saw.  The tough part is finding one since the Laguna 1412 came out about 6 months ago.   

 

Full disclosure, I ended up purchasing the Laguna and I am very pleased with my purchase.  I haven't done a whole lot with it yet (since I had to rearrange my shop for the new tool), but I plan on posting a review soon.

  • Author

Thanks guys. Josh I look forward to your Laguna saw review.

What does your grandfather typically use a bandsaw for?  Are you working with a tight budget?

 

I have the 10-325.  I agree with Nick, it's an OK saw - it's not the best, but it does everything I need it to (at least, so far).  For the right price, I think it's a good value.

 

- I have not had that problem with the upper post but like most things it could be something that affects individual saws.  

- I also don't much care for the bearings given how they move when you tighten them but you can get them aligned. Replacing them is on my "to-do" list, but it's pretty far down on the list.  

- The metal plate over the DC port is a complete nod to lawsuits and liability and is easily removed (I suggest doing so only if you have it permanently connected to a DC hose - just in case little hands are ever around).  

- The lamp seems silly - I mean, it 'helps' but it would be nice if the arm was a little longer so you could get more light on the cut line.

- I don't care for the table trunion - it's not exactly finely machined, but it works.  Getting the table square to the blade left-to-right (with the tilt) is easy, but I had an issue with it front-to-back because of the slop in the trunion.  I ended up having to shim the 2 front mounting bolts of the table and now it's dead on.  

 

You should never have to pay list price for this - at full price, there are better options.  But if your budget is challenged, and it's on sale, you should give it a look. 

  • Author

John,

He's mostly a tinkerer. Small projects. No real heavy resawing but I don't want him to be limited from it either. My budget is around 1k'ish. It's sounding like the Rikon isn't all that I was expecting it to be. That shifts me back to the grizzly option.

Don't want to come off like I'm overwhelmingly negative with the saw (it may yet be the best "bang for your buck" choice if on sale), it does have it's positives like the table, which is big and wonderful and not difficult to get aligned with the blade. And I think it's in the same ballpark with Grizzly products where they are fine and get the job done, just some nuisances and shortcuts to deal with in exchange for the lower price. But if the budget is a grand, I would definitely be batting my eyes more in the direction of the Lagunas.

I have the 10-325, and have very few complaints.  Adjusting the bearings takes some getting used to but my blades switches are down to less than 5 minutes now...and I just organize the work to minimize the switching.  In the future I will probably get a different blade so I would switch even less.  But my post doesn't move much at all when I raise/lower it, so that might be a one off problem.  I've resawed some 11" wide mahogany, 8" white oak, and probably another 100 bdft or so of other woods with no problems.  Basically it has done all I've asked of it.  I have used the Laguna and it might be a slightly nicer machine, but it all depends on your use, and price point.

 

I think the thing to take away from most of these posts is that all the saws works fine, rather well really (in my opinion), and the differences between them are in the fit and finish, which while it can be important, does not mean the saw won't work. Yes the position of the light is silly, but the Laguna doesn't come stock with a light...which is better?  The finish might be better on an Italian Laguna, but I've heard bad things about the Taiwan ones where the trunion couldn't even be shimmed to work. I don't know where the 1412 is made.  Customer service is something I have heard good and bad stories about all three companies (Laguna, Rikon and Grizzly)

 

I think any of the three would work well for most home shops.  Just depends on how a bandsaw fits into your workflow how much you want to spend on it.

I chose the Rikon when I purchased my saw (mid 2011), because it was the best on the market at the time in my opinion (when I considered the specs & price).

 

I've seen one Laguna 1412 and I question some of the specs/marketing.

 

  • They quote 1" blade capacity, and i don't think the spine is big/rigid enough to properly tension a 1" blade, even a narrow one.
  • I don't know why they didn't put the blade slot in the table like the Rikon. It's to the side, so you have to rotate the blade 90 degrees to get it out.
  • I don't like that the blade tension wheel is under the top wheel housing. I like it when they are on top because the screw is under tension then, and it isn't in the work area.
  • It uses ceramic guides, and I prefer the ball bearing type
  • The wheel base they show in all the marketing photos is a $149 option.

 

I can't speak to the grizzlies, as i haven't been to the outlet/warehouse since 2008, and I can't remember how I felt about them back then.

The posts by Josh and EotW above made me realize that I didn't post what I do like about the saw.

- Table - Good sized table, flat flat flat. I did have to shim it, but adjusting the angle with the rack and pinion system works well.

- Fence - once adjusted, the fence works well.  Are there better ones?  maybe.  I don't have a need to change it.

- Power - I resawed 8" oak and it worked very well.  yes the bearings are finicky to adjust but once dialed in, it cut nice and straight.

- DC - Yes the metal plate over the DC port seems silly, but even with that I would say the DC is 'good'.  

- Tensioning the blade seems to me to be easy.

- the detensioning handle works well and is never 'in the way'.

- I like having storage in the lower base, and it's not taken up by the motor.

I know some folks will say it`s a bad saw, but I looked long and hard at 14" Bandsaws before I bought one and I got the Shop Fox W1706. I know it only has a 1hp motor but I have re-sawn some walnut and some Sissou or AZ rosewood some green and some seasoned and it works great. Setup was easy and I like the fact that with the extension for it I have 12 3/4" of re-saw capability. I also like the tensioner that works very well and the table is flat, flat, flat. Yes it could have a better fence but any bandsaw under 2K could. It`s a heavy sucker being all cast iron with cast wheels as well. It runs smooth and quiet and only one bearing is a little hard to get to but not bad. I got mine for $560 and the extension for $69 here last year. I made a re-saw extension for the fence and it was simple. So far I have had no problems and it does a fine job of dust collection with my 2hp dust collector. Just another thought.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.