Recommended Posts

Posted

After seeing some of the random work I've done, an Aikido dojo in Washington DC asked me to make a torii (freestanding gate) for them to use as part of their kamiza (head seat/focal area). Since torii are supposed to mark the boundary between the outside world and the sacred (or, at least, denote an area that is more "special" - this usage does kind of make sense. Using Chris Hall's excellent gate guide, I proposed a couple options (all maintaining the proper 1:3:1 horizontal dimensions, and settled on a kashima torii. Basically, it's 2 vertical posts with an angled lintel at the top, and a small lintel below that is locked with opposing wedges).

 

post-6112-0-24964500-1390880169_thumb.jp

 

They had some sword racks built out of oak and stained "walnut"... so they asked for black walnut to match. The pieces were all milled from rough stock, and cut/finished by hand (except for the mortices - cutting a 4 x .75" through mortice in a 4" thick piece of walnut did not sound like fun, so I used a drill press for the waste. It came together fairly well, though I had problems getting the tenon shoulders to sit properly. My homemade shoulder/rabbet plane worked out well, though.

 

The boards were smoothed without sandpaper (well, except for some 600 grit sandpaper between oil coats) - which taught me some valuable lessons about stock selection. If I do this again, I will budget for clearer wood. My spokeshave actually saved me on this in multiple places where the grain was too odd for my smoothing plane to take a clean shaving. The actual finish is tung oil.

 

It's held onto the wall by a metal cleat (recessed into the top lintel) and screws/keyhole mounts at the bottom of the legs to make sure they stey on, even if the wood moves. Oddly, installation had me working in a fairly traditional Japanese manner - sitting on a tatami, with the piece propped up on 2x4s, using a ryoba to trim 2" off the bottom of the legs because the initial measurements were wrong. For the record, that was after 3.5 hours of sword practice, so I was tired and stiff, and really wishing for my (power) miter saw right then.

 

A couple closeup photos...

post-6112-0-22212200-1390880446_thumb.jp post-6112-0-13644600-1390880447_thumb.jp

  • Like 1
Posted

Some random in-progress shots.

 

After milling and rough cutting the pieces:

post-6112-0-18783200-1390881034_thumb.jp

 

I managed to mess up the top piece and instead of cutting a tongue and groove, I cut two grooves. Oops. Fortunately, cutting spline fixed it. Still, pretty dumb.

post-6112-0-28177200-1390881035_thumb.jp

 

Making sure the lower lintel fits.

post-6112-0-24227200-1390881036_thumb.jp

 

I was shocked to see everything actually fit together, and even square up. I was worried I badly mis-cut something, and would have to redo an entire piece (or two). I've never made anything this big before outside of framing walls, so I measured everything 5 or 6 times before cutting.

post-6112-0-41475800-1390881037_thumb.jp

 

A close up of the opposing wedges for the lower lintel. The lintel forms a cogged joint with the through mortise, and opposing wedges are tapped in to lock it in place. I cut the angle on the wedges by hand, and they were just different enough that I ended up using a stamp to mark which wedges pair up.

post-6112-0-31119100-1390881038_thumb.jp

Posted

Even more in-progress photos.

 

Oiling, oiling, oiling. I posted one or two of these in another thread. I purposely picked the boards with sapwood for the grain and color variation.

post-6112-0-25473000-1390881549_thumb.jppost-6112-0-55283500-1390881550_thumb.jppost-6112-0-63405200-1390881551_thumb.jp

 

Final assembly (well, before being disassembled to fit in my car, and re-assembled and installed).

post-6112-0-70899600-1390881552_thumb.jp

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 44 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined