Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Once dry, always dry?

Featured Replies

Absolutely new to this forum, but impressed with the knowledge.

 

I've some maple that was kiln dried 14 years ago.  It has been outside, but completely under cover since.  I live in Northwest Arkansas where we have moderate to high humidity in the summer.  Within reason, will the maple remain dry or is it time for another trip through my (soon to be) solar kiln?

 

Thanks,

 

Jim

Hold on - food for thought. I ran this question by http://www.bobkloes.com Bob Kloes is a friend of mine and a furniture maker. Bob sells a lot of hardwoods and has a buddy that kiln drys Bobs green lumber.

 

Bob said its best to run through the kiln for at least 24 hours to kill any insect activity/eggs in the wood since its been outside for so long. 

 

Hope this helps.

 

-Ace-

 

If you have any question, send him an email. 

Hold on - food for thought. I ran this question by http://www.bobkloes.com Bob Kloes is a friend of mine and a furniture maker. Bob sells a lot of hardwoods and has a buddy that kiln drys Bobs green lumber.

 

Bob said its best to run through the kiln for at least 24 hours to kill any insect activity/eggs in the wood since its been outside for so long. 

 

Hope this helps.

 

-Ace-

 

If you have any question, send him an email. 

 

Its called sterilization and you need a kiln that will boost core temp to about 140f for 3-4 hours. At normal kin temps it won't do a thing for the bugs if you have any. You dont want to sterilize for more than a couple hours if you have the ability. If your going to re kiln the lumber you need to run your normal drying schedule at regular temp and when it hits the final MC run the sterilization or it will ruin your lumber.

Its called sterilization and you need a kiln that will boost core temp to about 140f for 3-4 hours. At normal kin temps it won't do a thing for the bugs if you have any. You dont want to sterilize for more than a couple hours if you have the ability. If your going to re kiln the lumber you need to run your normal drying schedule at regular temp and when it hits the final MC run the sterilization or it will ruin your lumber.

 

The time in the kiln is based on how thick the wood is, temperature and all that jazz. Its best to consult the people who do this kind of thing on a daily basis. There may also be a way to handle insects with chemicals. 

 

-Ace- 

The time in the kiln is based on how thick the wood is, temperature and all that jazz. Its best to consult the people who do this kind of thing on a daily basis. There may also be a way to handle insects with chemicals. 

 

-Ace- 

 

Actually what I stated came directly from the kiln operator for McFarland cascade.

Actually what I stated came directly from the kiln operator for McFarland cascade.

Actually what I said came directly from Bob Kloes. He does this stuff every day.  Not trying to pick a fight. Think of it in terms of cooking a thick piece of meat  vs. a thin piece of meat. A very thin piece of meat takes less time to reach temp. Does that make any sense?

 

-Ace- 

Unless you are talking logs, the lumber thickness is accounted for in that "couple hours." This is not food that needs to be calculated to the nearest 30 seconds. Honestly I am not sure what you might need to sterilize. If you left the lumber near the bugs we worry about inside the shop, you would not find lumber that still has good integrity. You'd need to cut the punk off and would want to do this outside. BTW, sterilization is one of the narrowest scientific fields in woodworking. This comes from the international regulatory bodies that forbid the transmission of microorganisms across the seas and borders.

Actually what I said came directly from Bob Kloes. He does this stuff every day.  Not trying to pick a fight. Think of it in terms of cooking a thick piece of meat  vs. a thin piece of meat. A very thin piece of meat takes less time to reach temp. Does that make any sense?

 

-Ace- 

 

No thats why you have to measure core temp for sterilization. Just as you would a roast or turkey the core temp is what counts. To kill bugs your 100 degree kiln will never bring core temp up high enough to kill the bugs. It takes raising kiln temps up to 170+ to quickly bring core temps up to 140 and from there the clock starts ticking before the material is junk.

Unless you are talking logs, the lumber thickness is accounted for in that "couple hours." This is not food that needs to be calculated to the nearest 30 seconds. Honestly I am not sure what you might need to sterilize. If you left the lumber near the bugs we worry about inside the shop, you would not find lumber that still has good integrity. You'd need to cut the punk off and would want to do this outside. BTW, sterilization is one of the narrowest scientific fields in woodworking. This comes from the international regulatory bodies that forbid the transmission of microorganisms across the seas and borders.

 

Most kiln operators offer sterilization especially if you live in an area with beetle issues. I have a little 20ft woodmizer but it won't even come close to sterilization temps but really never found the need in the PNW. 

They key here is that the temperature must be held at 130-140 for at least 24 hours once the lumber reaches this temperature.  In other words you aren't looking at the temp gauge of the kiln but the temp of the wood in the kiln.  Most schedules will slowly raise the temperature over time so that the wood does have time to heat all the way through before the temp is notched up again.  This is what the schedule is for, otherwise you run the risk of honeycombing.

 

Regarding the original question, no once lumber is dry it will not always be dry.  However a kiln dried wood will change more slowly than an air dried wood.  KD wood is essentially baked in the oven and the cell walls harden a bit as it is baked.  I compare this to bread place in the toaster or the oven.  Bake it and it gets hard and will snap in half.  Once done, the lumber is not quite as flexible as it was before (one reason why steam bending kd wood is a bad idea) so it will resist increases in moisture longer than air dried material.  In other words, it is more stable.  In general if we have have KD lumber that sits in the sheds for more than 6 months we will redry it back down to 6-8%.  It doesn't take long as the drier, harder cell walls will evacuate the moisture much faster much like a dry creek bed after a rain storm. 

 

Enough metaphors yet?

No thats why you have to measure core temp for sterilization. Just as you would a roast or turkey the core temp is what counts. To kill bugs your 100 degree kiln will never bring core temp up high enough to kill the bugs. It takes raising kiln temps up to 170+ to quickly bring core temps up to 140 and from there the clock starts ticking before the material is junk.

 

Hmm....not sure why you have to bring the core temp up so rapidly and quick unless your in a rush? Isn't that how kiln operators get in trouble. They case harden. Where just heating to warm the bugs and eggs that get deep into the wood, just enough to kill them. If the wood is already kiln dried the cells of the wood are already compressed that's what kiln drying does. 

 

-Ace-

Hmm....not sure why you have to bring the core temp up so rapidly and quick unless your in a rush? Isn't that how kiln operators get in trouble. They case harden. Where just heating to warm the bugs and eggs that get deep into the wood, just enough to kill them. If the wood is already kiln dried the cells of the wood are already compressed that's what kiln drying does. 

 

-Ace-

 

It take 130 -140 to kill bugs like beetles but the temp destroys material so you have to bring it up fast do your killing quickly and bring it back down before you damage the material and part of the reason you do it at the end of the cycle.

They key here is that the temperature must be held at 130-140 for at least 24 hours once the lumber reaches this temperature.  In other words you aren't looking at the temp gauge of the kiln but the temp of the wood in the kiln.  Most schedules will slowly raise the temperature over time so that the wood does have time to heat all the way through before the temp is notched up again.  This is what the schedule is for, otherwise you run the risk of honeycombing.

 

Regarding the original question, no once lumber is dry it will not always be dry.  However a kiln dried wood will change more slowly than an air dried wood.  KD wood is essentially baked in the oven and the cell walls harden a bit as it is baked.  I compare this to bread place in the toaster or the oven.  Bake it and it gets hard and will snap in half.  Once done, the lumber is not quite as flexible as it was before (one reason why steam bending kd wood is a bad idea) so it will resist increases in moisture longer than air dried material.  In other words, it is more stable.  In general if we have have KD lumber that sits in the sheds for more than 6 months we will redry it back down to 6-8%.  It doesn't take long as the drier, harder cell walls will evacuate the moisture much faster much like a dry creek bed after a rain storm. 

 

Enough metaphors yet?

 

Not sure about re-drying wood that was once already KD just for the sake of drying just to have it go back to the moisture content that is outside the kiln.

 

Think about soaking kiln dried wood in water, before bending or even steam bending. My experience, the wood almost always shrinks down back to original size. Or pretty darn close (maple and poplar). The cells wont re-open to air dried size will they?

 

-Ace-

It take 130 -140 to kill bugs like beetles but the temp destroys material so you have to bring it up fast do your killing quickly and bring it back down before you damage the material and part of the reason you do it at the end of the cycle.

 

What damage are you talking about?

 

-Ace-

Hey Ace, you ask about moisture content and heat without considering the blend. You keep wood from over drying by keeping kiln humidity high while raising the temp for sterilization. This process does not require drying your lumber beyond a moisture content appropriate for your region. The thread started with recommendations to not re kiln for any purpose but sterilization.

  • Author

Wow!!  Thanks to all.  I must say you're a lively bunch.  I enjoyed the banter.  I'll check for bugs and the moisture content when the weather warms up.  Right now it's a bit chilly here.

Hey Ace, you ask about moisture content and heat without considering the blend. You keep wood from over drying by keeping kiln humidity high while raising the temp for sterilization. This process does not require drying your lumber beyond a moisture content appropriate for your region. The thread started with recommendations to not re kiln for any purpose but sterilization.

 

Sorry not understanding your statement.

 

RWW mentioned he dries wood that is over 6 months old in the kiln to be re-dried. That's interesting to me, why do that? In the wintertime your wood has less moisture than during humid summer time, yes? So if your wood is 6 months old and say it's stored indoors and a non insect issue, why run it in the kiln? The point here is Burgiej stored his KD wood outside. The concern should be insects - not to re-dry KD wood for moisture because it its what it is.  

 

-Ace-

Hell its all good conversation. Re drying will just bring mc back down to closer to indoor mc. I guess it would get the wood back to a workable point quicker than just setting in the shop. Over cooking at to high of temps for to long makes the wood unworkable and brittle. Its a balancing act between temp and rh. I don't even want to understand the math it's to complicated to even worry about.

Hell its all good conversation. Re drying will just bring mc back down to closer to indoor mc. I guess it would get the wood back to a workable point quicker than just setting in the shop. Over cooking at to high of temps for to long makes the wood unworkable and brittle. Its a balancing act between temp and rh. I don't even want to understand the math it's to complicated to even worry about.

 

That's my point....thanks for summing it up!

 

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.