Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

A simple finish for cherry

Featured Replies

I'm a beginner woodworker, and even more of a beginner when it comes to finishing. I built a little wine rack, which is little more than a box with an X in it. Got a little creative and put in some ebony splines to add an accent. Still needs some more sanding and clean up. Now it's time to think about a finish. I have not developed the ability to do much other than a very simple finish, such as a wipe on varnish. And I do not have access to spray equipment or anything more complicated than a rag or foam brush.

I have sanded the piece with 120 grit, and sanded the end grain to 220. I was thinking of finishing this piece first with a layer of Seal Coat sanding sealer (wax free shellac), then light sanding, then three layers of Arm-R-Seal oil and urethane topcoat (light sanding between coats) all applied with a foam brush.

Any thoughts for a beginner? I'd like to avoid blotches and keep the wood as light and natural as possible.post-15561-0-14182700-1399237832_thumb.j

Love the splines!

 

You might find you want to sand it all over to 220, maybe even higher before you start the finishing process. You will notice a difference when you run your hand over it.

 

I don't have a lot of experience with cherry, but I'm told it is prone to blotching so shellac is a good start. Depending on what type of shellac (blonde vs amber) you might even like just a few coats of shellac and be done with it. Shellac is very easy to work with.

 

Ultimately, if you have some off cuts from your project, I would sand some of that to the same degree as the project, do some tester boards and see what you think! You might even want to sand a test board to 220 before doing the whole project to see how you feel about the whole project being like that.

Only problem with shellac is it's going on a wine rack...one spill and bye-bye shellac.  I'm gonna be boring and say satin or semi-gloss Arm-R-Seal.  Easy, protective, looks great.

Lose the shellac for arm-r-seal. I use Charles Neil's blotch control, for staining. But this shouldn't blotch if you are just using a top coat and not stain. Arm-r-seal shouldn't make it blotch.

+1 for Arm-R-Seal.  I like semi gloss on cherry. 

 

For a wine rack I might even consider going with just BLO and wax, though it would require maintenance.  

 

But I would probably just go with the Arm R Seal.  

 

And yes, sand to 220.

  • 3 weeks later...

I think you are on the right track with ArmRSeal, as far as wipe ons go, I think that is the best of the bunch.

 

I'd think about starting with a coat of boiled linseed oil, let that sit for a week or two so then hit it with the ArmRSeal.  You might also think about doing a coat of thinned shellac but mix in 20% amber -- I have found that really warms up the grain.  Brushing shellac on that might be difficult though -- I'd make a few test boards but probably lean toward BLO/ArmRSeal for the simplicity and low risk.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.