ResidentEvil Posted December 5, 2014 Report Posted December 5, 2014 Ok. So I'm not actually making a curvy cutting board, but am using that technique to make a table top for an entry way table. My idea is to have two thinner curves, maybe 1/4 or 5/16 out of a single piece of wood inlay. Then a third curve that is wider, maybe 1/2", where the inlay is 5 very thin pieces of laminated woods with alternating/contrasting color tones. Very similar to Scotty Lewis' "coolest cutting board ever". The process I was going to use to cut out the curves is as follows: 1. Make template out of mdf with my desired curve 2. attach template to table top and use a top bearing template router bit to define the curve. The router bit diameter should be the exact width of the thickness of the inlaid wood. A shallow pass with the router defines the curve on the top. 3. Use a bandsaw to cut through the routed curve to separate the to halves of the top. 4. Use a larger diameter (diameter doesn't matter at this point) pattern bit on the router table to clean up the cuts, using the initial cut as the template for the router bearing. 5. Glue the top back together with the inlay in place The steps above are done three times, once for each inlay. If I didn't explain that well, search "coolest cutting board ever" on youtube and you'll see the process I was trying to describe. My problem: I need a 1/4" or 5/16" diameter straight bit with a top bearing, but I can't find one anywhere. The smallest diameter bit with a top bearing I could find is 1/2". I'm sure I just have a case of the dumbs tonight, but I was hoping that someone could point me in the right direction. Quote
Vyrolan Posted December 5, 2014 Report Posted December 5, 2014 Just use a bit of the right size with a standard guide bushing? You'll have to offset your pattern slightly to account for bushing outer diameter bigger than bit diameter, but you should be able to guide the bushing along your template close to as easily as a bearing. Quote
..Kev Posted December 5, 2014 Report Posted December 5, 2014 I see where you're going but, in reality, the diameter of the bit doesn't really matter. The goal here is just to get a super clean cut. I've showed my process for doing these a couple times here.. If you're clean enough at the band saw, you don't need to use the router at all. Quote
Vyrolan Posted December 5, 2014 Report Posted December 5, 2014 TIODS, I was thinking he was wanting to do it this way because it's a table top...with that size and weight, it's going to be a lot more difficult to get a smooth clean cut unless he has a really nice saw and decent skill. His way is slower but is probably more robust. JM2C 1 Quote
..Kev Posted December 5, 2014 Report Posted December 5, 2014 TIODS, I was thinking he was wanting to do it this way because it's a table top...with that size and weight, it's going to be a lot more difficult to get a smooth clean cut unless he has a really nice saw and decent skill. His way is slower but is probably more robust. JM2C You are correct, I misread that.. Thanks! Quote
ResidentEvil Posted December 5, 2014 Author Report Posted December 5, 2014 I see where you're going but, in reality, the diameter of the bit doesn't really matter. The goal here is just to get a super clean cut. I've showed my process for doing these a couple times here.. If you're clean enough at the band saw, you don't need to use the router at all. My other reasoning for this (other than the table top thing) was that using a router to remove the same thickness as what I'm using to inlay will allow the grain of the board to realign perfectly. If I were to draw the cut on the board and then cut with a bandsaw, then I'm only removing the thickness of the band saw blade. If I'm inserting a 1/4" thick inlay, then the grain on the board will be shifted over by that much. I'll go back and read through your cutting board thread to see if I'm off on this thought. Quote
ResidentEvil Posted December 5, 2014 Author Report Posted December 5, 2014 Just use a bit of the right size with a standard guide bushing? You'll have to offset your pattern slightly to account for bushing outer diameter bigger than bit diameter, but you should be able to guide the bushing along your template close to as easily as a bearing. After looking some more I found a 5/16" diameter bit with a bearing that was just a slight bit wider. That would work as well, I'd just have to offset the pattern a bit to account for the extra bearing thickness. Though I'd rather find a bit that is 1/4" with a bearing to match. I figured I was just being my normal obtuse self and for some reason couldn't find it. Seems like these types of bits would be readily available, but maybe its a safety issue I'm not thinking of or something. Quote
Shane Jimerfield Posted December 5, 2014 Report Posted December 5, 2014 did you check Whiteside's collection? Quote
dwacker Posted December 5, 2014 Report Posted December 5, 2014 It would be pretty hard to have a 1/4" shaft with a 1/4" cutter and a 1/4" bearing. 1 Quote
ResidentEvil Posted December 5, 2014 Author Report Posted December 5, 2014 did you check Whiteside's collection? Yep. Smallest they have in a pattern bit is 1/2" It would be pretty hard to have a 1/4" shaft with a 1/4" cutter and a 1/4" bearing. I knew there was something really simple that I was overlooking. [homersimpsonvoice]DOH[/homersimpsonvoice] I guess plan B is Vyrolan's idea. Guide bushing with a regular straight bit. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.