Raefco Posted December 27, 2014 Report Posted December 27, 2014 most oilless units just have a sealed bearing at the rod/crank connection, covered by a plastic shroud. I had a stacked tank unit I used on job sites for almost 20 years. It got sat in front of a heater and it melted the plastic case off of it, LOL, so for years every time it kicked on you could see the crank, piston rod, and piston going to town. The stacked tank really helps keep water out of the lines and no more volume used by a small nail gun you shouldn't get much in the lines but if you put it in the attic, or any unconditioned space, you may notice condensation on the outside of you air lines or your in nail guns. …and the small unit sitting in my garage, plumbed into the basement, will trip the reset on the compressor when it is very cold out side (it is a 2hp oiled unit) Quote
Tpt life Posted December 27, 2014 Report Posted December 27, 2014 …and the small unit sitting in my garage, plumbed into the basement, will trip the reset on the compressor when it is very cold out side (it is a 2hp oiled unit) A light bulb nestled against the oil resevoir for about five minutes fixed this for us. Quote
bgreenb Posted December 28, 2014 Report Posted December 28, 2014 I've got the PC pinner and also the PC pancake compressor. I'm very happy with both. I actually got rid of a much bigger Makita compressor because I simply didn't need it. Not much to say other than the PCs do the job well. Like you, I turn my compressor on a couple times a month. When I turn it on, it works. Not much to say more than that. Get the PC and save your money for more festool and lie Nielsen. Quote
estesbubba Posted February 2, 2015 Report Posted February 2, 2015 Cool, thanks. Are you talking about this one? http://www.lowes.com/pd_470437-70-PCFP02040_0__?productId=50015924&cm_mmc=search_google-_-Tools-And-Hardware_rtc-(1)-_-Porter-cable_pcfp02040-_-porter%20cable%20pcfp02040&k_clickID=3d91cb72-c8f3-48d1-992c-57bdd61c9fc8 And I'm hearing you correctly that if I installed an auto drain solenoid that I wouldn't have to worry too much about moisture collecting in the lines? Just give it a kick with an air chuck every once in a while? That sounds good to me! Eric - did you end up getting this compressor? I'm also thinking of getting a small one for my shop since I don't see a need for a big one. Quote
Eric. Posted February 2, 2015 Author Report Posted February 2, 2015 No I ended up with the Senco... http://www.amazon.com/gp/product/B0000AQK78/ref=oh_aui_detailpage_o02_s01?ie=UTF8&psc=1 It's tiny, quiet, cheap, and plenty good enough for what I need. Quote
CessnaPilotBarry Posted February 2, 2015 Report Posted February 2, 2015 Once you pick one, I learned a neat pinner trick for furniture a few years back... With a 1/4" spacer (MDF, shim, etc...) under the body of the gun, shoot a few pins into an area where you need to glue two parts together, where the glue will go. The tip should not be in contact with the wood, you want the pins only partially driven. Snip the pins off ~ 1/16" above the surface. Apply glue and clamp the parts together... The "pinlets" will prevent the parts from slipping or creeping when clamped, and nothing will be visible in the surface, or affect planing or sanding. This isn't something you'll use every time, but it's golden in certain situations. 2 Quote
Raefco Posted February 2, 2015 Report Posted February 2, 2015 So, have you ordered it yet, I have a set of 4 blue hawk, 2 finisher nailers, the stapler and a pin nailer. I had never even used the pin nailer till I seen this thread, I have had more "WTH was I think moments" than I care to mention since joining this site. Quote
estesbubba Posted February 2, 2015 Report Posted February 2, 2015 Just picked up that PC compressor Eric listed above at Menards for $119! http://www.menards.com/main/p-2427430-c-12910.htm Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.