Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Front Vise Choice

Featured Replies

I'm finally getting around to buying a front vise for my new bench. I've been trying to decide between the one offered by Lee Valley ($85.00), which doesn't mention a brand, and the Wood River Large Front Vise, for $99.00, listed in the Woodcraft catalog. Does anyone have either of these and can attest to their quality? I already purchased a LN clamp-on dovetail vise so this will be for general holding where I want something clamped a little lower. The bench already has an end vise. 

I got mine from Peachtree Woodworking, but all 3 seem to be similar asian made vises. Ptree is currently out of stock on these so I would just compare the capacity and part sizes. Mine is a quick release version and while convenient I think it will not last as long as the simpler mechanism.

  • Author

Simpler is always better in my mind as well. I will be near the Delaware Woodcraft store tomorrow and I'll check theirs out. If I find no faults with it the lack of sales tax balances out the shipping charges from ordering elsewhere. I'm sure I'll find a few other goodies while there.  :rolleyes:

I purchased a large Jorgenson 10" vice based on Fine Woodworking reviews. It's rather expensive ($175) but works very well. A vice is something you use everyday so I figure I shouldn't skimp...

I too have the Jorgenson 10" with quick release. After 3 months, I'm just getting use to the quick release part, having never used one. I would buy it again, but as much of a beast as it is, I'll never have too.

  • Author

I ended up going with the Wood River. It is indeed essentially the same casting as in the what Grizzly and Lee Valley sell from what I can tell. Grizzly sells it for quite a bit less, for some reason, but I got quite a few other things while at the Woodcraft store. The instructions that Lee Valley have available for downloading on their site are much clearer than the ones Woodcraft include so I am following both when installing it. They actually did have a single boxed Jorgenson bench vise on the shelf, with no display model, but I was pretty well set on a vise without metal faces anyway. I haven't installed it yet. My bench has a three inch thick top but no apron so I am first going to get some maple to extend the bench face down a bit, and also for the front vise face.  

A lot of the difference in asian made castings is the level of finishing/ machine work , accessories, and quality control. The rejects from the most particular company may still satisfy one with broader standards of acceptance.

Better packaging and instructions can add to the cost as well.

  • Author

I’m re-thinking my plan to mount a piece as a lower extension of the bench front for the screw and guide rods to go through. While I’ve seen a few pics on various sites of just that being done, I’ve seen just as many where the wood on the front vise face extends well below the bench face.  Am I really gaining anything if the board I end up working on can sit no lower than the vise’s guide rods anyway? Or will the block I mount and run the guide rods and screw through give additional support to the guide rods? Forgive these rookie questions.   :)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.