Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Bakers Table in need of sealing, gaps to fill.

Featured Replies

If they are selling it as hard maple it probably is. But for something like this even soft maple should work fine. Telling the difference between the two at the lumber yard is difficult. Keep in mind "soft" maple is only soft relative to hard maple. It's still a very hard wood.

  • Replies 64
  • Views 15.7k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Brendon_t
    Brendon_t

    keep in mind, being vegas, any wood being stored outside at a yard should really be brought inside and allowed to acclimate for a while before being turned into anything.

  • I'm for rebuilding as well. The last thing you want are sick customers. Google Blue Bell Ice Cream.

  • So basically you want to call both places and find out how much they are charging for 8/4 (pronounced eight-quarter) hard maple. And find out whether it is sold rough, s2s or s3s. Milling rough stock

Posted Images

remember there is a difference between absolute and relative humidity. the moisture in the air at 10 percent relative humidity at 100 degrees, will be more than the absolute moisture in the air at 10 percent humidity and 60 degrees. 

 

fundamentally, i doubt you even notice it with this project

Nice stack. Not sure when your brother is coming out but if it's not very soon, make sure you have those boards stickered and off the ground

  • Author

Nice stack. Not sure when your brother is coming out but if it's not very soon, make sure you have those boards stickered and off the ground

Thanks. We will be slicing and dicing day after tomorrow. What does it mean to sticker the wood?

Can it sit flat on my cement porch that's covered?

Stickered means to stack it in rows with 1" or so sticks every 18" or so that air can properly circulate around the board.

I personally would not leave it down on concrete. Concrete has the tenancy to wick up moisture.

  • Author

Stickered means to stack it in rows with 1" or so sticks every 18" or so that air can properly circulate around the board.

I personally would not leave it down on concrete. Concrete has the tenancy to wick up moisture.

Got it. It's off the cement. Should it be ok supported in three places in the middle, about 3 feet apart until Saturday morning.? I threw some shade cloth over it although it only would get afternoon sun for an hour or two.

  • Author

Well, we got a pretty good start on the table this weekend. Saturday we took a fair bit of time figuring everything out, getting a decent kerf blade, and doing some rough chops of the stock. Yesterday a little more tangible progress, ripping up and planing smooth the 1" stacks for the backsplash/cove. We are  T&Ging them and we got as far as glueing up the top portion of the rear backsplash. 

 

post-18067-0-88836200-1435007403_thumb.jpost-18067-0-39156500-1435007417_thumb.j

 

My brother left the equipment to come up and hopefully finish next weekend. Now to see what progress I might make on my own this week. I am not totally confident enough to risk this 'spensive wood on my low skill level. Will proceed with extreme caution! 

It's looking good.  Not that it matters at this point because you've already done it...but that tongue and groove was a complete waste of your time.  A long grain to long grain glue joint is stronger than the wood itself and needs no mechanical reinforcement.  But what's done is done...it'll help with alignment when you glue up if nothing else.

  • Author

It's looking good.  Not that it matters at this point because you've already done it...but that tongue and groove was a complete waste of your time.  A long grain to long grain glue joint is stronger than the wood itself and needs no mechanical reinforcement.  But what's done is done...it'll help with alignment when you glue up if nothing else.

Thanks. And yup, that's mostly why we did it . . . to help the glue job.  Also I think it will look kinda cool on the forward edges of the side splashes. But then I'm easily impressed. 

 

For the same reason my brother is suggesting we domino the 1 3/4" slats for the body of the table top with the Festool. Whaddaya think? I'm imagining three or four dominoes spaced apart between each 34.5" length of square 1 3/4".  (Maybe three would be plenty?)

  • Author

Oh no. I first glued up the 21 slats in four sections. That's how they are now. When I mated the four sections to check the joints (before glueing the 4 sections together) I noticed a bend had developed in one of the sections and I could not completely close the .030"-.045" gaps on the ends with clamping. It's already better overnight. I have a humidifier going on low and every so often I tweak the clamps a little and it closes a little more. Over time, will it close completely and be as tight as the rest of the table?

No. even if you successfully clamp it closed, it will likely re-open with time.

A better solution is to rejoint the edge and then glue.

  • Author

Thanks, that's what I will do. We have a festool tracksaw that should do the job.  I have to put this project to bed for two weeks of work-related travel. Should I just clamp it up so it doesn't become a runaway train while I am away? 

Any time you attempt to force gaps closed with pressure and manipulation, you are working against the wood and opening yourself up for joint failure down the road. Clamping the slats in sub assembles was a good idea, now take the same principals to the larger "slats". Joint the edges to a true flat length and 90* to the face then glue up.

Set yourself up for long term success, not short term time savings.

  • Author

Got it. That is the new plan then. Any need to clamp them together for stable storage while I am away for two weeks? 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.