Cliff Posted November 5, 2015 Report Posted November 5, 2015 So I have a Ryobi AP-10 planer. It was given to me by a lady whose dad owned it. If I had to guess, it's the first one they made in 1985. In fact I have read that the Ryobi AP-10 was the first benchtop planer sold ever. I can download the manual online, but the one online, I think, is for newer versions where they have changed things. My issue is that I have one edge and face flat and square to each other. I pass the board through the planer, several passes - and test it for square and it's quite a bit off. I wasn't able to really get a reading off the rollers, but the entire head seems to be dipped slightly on the right side of the planer. the calipers said by about 2 mm. The manual showed bolts to loosen, then you adjust nuts to bring a side up or down. I absolutely cannot find them. I think they changed it. Anyone either owned an older one of these? Or a newer one? Maybe can help me out or take a picture so I know where to try and adjust? I'd appreciate it! Quote
rodger. Posted November 5, 2015 Report Posted November 5, 2015 (edited) Are the knives evenly set? Maybe something to check before taking it apart. Edited November 5, 2015 by Pug Quote
wdwerker Posted November 5, 2015 Report Posted November 5, 2015 I have an ancient Ryobi portable planer. I am pretty sure there is a chain & sprockets that raises and lowers the head. I am in the middle of cleaning out the shop and packing for the big move. If I come across the manual I will take a look but I can't make any promises Quote
Cliff Posted November 5, 2015 Author Report Posted November 5, 2015 I have an ancient Ryobi portable planer. I am pretty sure there is a chain & sprockets that raises and lowers the head. I am in the middle of cleaning out the shop and packing for the big move. If I come across the manual I will take a look but I can't make any promises Thanks! I actually suspected you may have run into this thing. I saw the chain, I just didn't see how to do anything with it. Appreciate the help - if you can. If not, no worries Are the knives evenly set? Maybe something to check before taking it apart.This is my first planer and I don't really know. All I can say for certain is that I used their tool to set the knives when I did it. I believe I did it right but I simply can't say for sure. In the manual I have it says to put a piece of paper on the bed, then put a level on top of that and test each side of the planer (the rollers sit on the level.) I noticed the right side was harder to pull it out. Then I used a gauge to test the distance to the head and came up with a difference. As for the knives - it basically says to use the tool, shows a picture of how it should look when you put it in. Quote
wdwerker Posted November 5, 2015 Report Posted November 5, 2015 An accurate pair of calipers helps when setting the blades in the carrier. If both ends measure exactly the same then it is the entire head that's off.Dial or digital calipers work . Getting the blades exact does take some finagling . I sharpen my blades with a jig on my Tormek. The jig was expensive back when I bought it, it's approaching ridiculous now ! But it does an incredible job and removes very little metal which extends the blade life. 2 Quote
Cliff Posted November 5, 2015 Author Report Posted November 5, 2015 I actually picked up new blades for it since they were on amazon. Now I have an old set that I can drop off at the sharpening place since I don't have any sort of grinder yet. When you say "if both ends measure exactly the same" - I'm not sure what you mean. I do have calipers. I'm not sure where to measure. Quote
wdwerker Posted November 5, 2015 Report Posted November 5, 2015 From the edge of the knife to the back edge of the black " L " shaped holder that the blade bolts to . Then the blade and holder bolts to the cutter head. 1 Quote
Cliff Posted November 5, 2015 Author Report Posted November 5, 2015 OK. I can try that tomorrow. Thanks! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.