Recommended Posts

Posted

I know I'm not the only one with troubles dealing with this machine. I struggled with the belt tension and tracking. I think I've got that under control. Cross my fingers. I kept tripping the breaker with it all the time and discovered that the belts were as loose as poop through a goose. That left belt residue throughout the motor compartment. They're sending me new belts. I tensioned them properly and no issues with that anymore. Now I want to change the paper on the drum. I've seen the video several times and at no time did it seem that it is difficult to do. I cannot, for the life of me, get it to not develop little gaps all along the way while wrapping it on the drum. I've gotten so frustrated with it that I want to take a sledge hammer to it. Please help me if you can. Sending it back is not going to happen. There's nothing wrong with it except a poor design making it difficult to operate and maintain. When I solved the other issues it has worked great and I'm pleased with it in that respect.

Posted

Getting the abrasive aligned properly does take some practice. I made a template from a factory cut strip that worked well. Mark the position where the clips hold the position where it was fitting and behaving the best. Sometimes re winding a strip and shifting the clamping position is all it takes . The cut length has to be pretty precise, angles too !

Posted

Don't worry about small gaps between the pieces.  It does not need to be toughing. Being that it is a spiral and not a straight gap, the 1/8"gap in paper will not affect performance. 

I used to line the paper with no gap.  The abrasive stretched and shifted creating a ridge. I later modified my cut angle on the paper specifically to give me a bit of gap so that if the tension spools all the paper to the right side of the drum,  it doesn't create a seam.

Posted (edited)

I made my template from 1/4" ply scrap. Clamp it down before cutting ! Mine shifted  because I was in a hurry and I ruined 3 strips that were too short. You can always cut one shorter but be careful being to generous or you will get less strips per roll.

Keep an eye on the abrasive and clean it w a crepe rubber block at the first sign of resin building up. This prevents burns . Don't try to take off too much in one pass, this causes burns too. Shut the drum off immediately if you see a darkening line appear on the outfeed side.

i have flood light bulbs in swing arm lamps aimed at a raking angle to highlight the board on both infeed and outfeed. I will mark the surface of the board with pencil lines every few inches and switch to a finer grit when all the lines are gone, repeat with each grit.

Brendon is right small gaps in the spiral are better than the paper touching.

Taking off too much in one pass and too fast a feed rate are the biggest things to avoid.

Edited by wdwerker
More info
Posted

Thicker as in wider or a thicker backer? 

Either way, it's not that hard to start with no template and make a strip that works. There are two angles at play.  If starting from scratch because of a different size abrasive,start toward the higher and step down incrementally until the paper loads the right side in a straight line and after the first wrap,connects closely to the start. The angle should be the same on the other side to terminate the wrap. 

Steve's advice above is also all spot on. Clean paper = proper sanding = quicker sanding/better results.

Posted

Brendon, It is 'wider' sorry,  wider by litteraly  a hair. I managed to get it within a half an inch. It looks real good so I think I need to cut another and make the tab that goes into the hold down a hair longer. Of course the rolls I ordered with it from Grizzly only yield 1 1/2 strips. I know I can use the rest of it but really only one more half??? This frustrates me even more because I have arthritis and after doing this several times I'm in a lot of pain. I hate those guys on their video, do it in about 4 minutes.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 67 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined