Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

refinishing problems

Featured Replies

Hi,   I am new to this so please bear with me.  I just built a living room set consisting of two end tables, a corner unit and a coffee table.  The bottom frame is all metal ( solid bar and hollow tubing, ) and the tops are all 7/8" solid oak, which I purchased all dressed.  I applied two coats of min wax dark walnut, 8 hours apart, and then applied a clear polyurethane over that.  I botched the clear coating and used wet sand 600 grit to remove drips and blotches I had left.  Then I tried to put a second coat of clear and just made a total mess.... lots of drips, and some dust showing thru. My daughter wanted the stain to be darker.  I did my best to take off the whole 2nd layer of clear and apparently took off some of the bottom layer to the staining as well.  I don't know what to do next.  Is there a way to salvage this, or do I need to take everything off down to the bare wood against and restart from scratch?  Help.  Thanks.

Hey Roland, when you say that you bought them totally dressed,  you mean pre finished or milled, cut, sanded and ready for finish? 

After the second coat of stain, how long did you wait before starting the clear coat? 

Are the blotches and imperfections centered around deep pores in the grain? 

You mentioned your daughter wanted it darker,  if you salvage the current look, will she be happy with it or are you considering stripping it back anyway? 

Pictures also can help.

Sounds like stripping, sanding and using dye instead of stain is your best bet. Dye will achieve those darker colors so much better than any stain, especially Minwax. You can stain over the dye coat to make the color even richer. Thin careful coats of finish !

  • Author

Hi Brendon,

My daughter would prefer the stain be darker, however, if everything else looks okay, she can live with the lighter colour.

As for the dressed issue, I was told the slab was originally approx. 1-1/4" and milled down , top and bottom, to approx. 7/8".  All four edges looked straight so they cut the slabs down to square, with everything being sanded.  I just assumed it was ready to be stained.  Now that you mention it, I seem to recall my wife telling me she thought all the pieces should have been sanded better.

The instructions on the stain, Minwax, wood finish, dark walnut, stated to wipe excess stain after 5-15 minutes.... I waited 15.   The 2nd coat after 4-5 hours, I waited 5.   ( no sanding between coats , as per instructions).   Then I applied the 1st clear coat after 8 hours.  It did recommend putting on a 2nd coat after 6-8 hours when still tacky.  I missed that part of the instructions.  I put the 2nd coat on the next day when I noticed small bubbles and drips.  Other than that , it was a decent job.  I should have left it.  Instead, my son recommended using wet sandpaper, 600 grit in small circular motions, wiping the white excess off  before proceeding with the 2nd clear coat.

I should mention the stain was put on with a brush, and then wiped down with a clean rag.    the clear-coat was put on with a sponge brush, both times.

I did that the 3rd day, under bad lighting conditions, and ended up with mega drips, and the coating pulling and streaking and spots that looked like I had missed.

I then used a sander with 220 grit and tried to remove the top clear coat only, but ended up taking more in spots, and even some of the stain in spots.

I don't know if I can salvage things or if it is better just to remove everything , stain and coats, and start from scratch, which will add valuable time to the project end date.

Currently, most of the clear is gone, but I have areas or spots, where there is still a shine from the clear.  I am afraid if I leave it, any new stain to try and cover won't stick to the clear.  If I totally remove the clear, then I know some of the stain will be taken off as well.  So then I would wonder if new stain will blend in with any remaining stain or stick out like a sore thumb.

I am a metal fabricator who wants to add wood to projects.  From afar, the tables looks awesome, but once you get within a few feet, it looks like an amateur did the woodworking ( rightly so I have to admit )

I await your response with anticipation.  Thanks

Roland

Hi wdwerker,

If I go the route of starting over, I think you are right.  I was raised believing that you had to sand in between stains.  Minwax says no to sanding in between stains.  I actually questioned this when I started the staining, but chalked it up to that is the way to stain in 2016.  Thanks for your input.

Roland

9 minutes ago, Roland Bernard said:

I am afraid if I leave it, any new stain to try and cover won't stick to the clear.  If I totally remove the clear, then I know some of the stain will be taken off as well.  So then I would wonder if new stain will blend in with any remaining stain or stick out like a sore thumb.

 

Yeah that's pretty accurate.   

Is this issue across all 4 pieces?

  • Author

Hey Brandon,

yes, I thought I could touch up the small imperfections and messed up all four pieces.  As much as I hate the idea, I think the right thing to do is to start over and get rid of all the shiny clear, and as much of the stain as possible.  I think , however, that if i leave the stain in the grains, it might help the overall to look darker after I give it one or two coats of stain.  So what is best, chemicals to take off the stain and clear to the bare wood, or sanding it all out?  ( by hand or with a sander )

I appreciate the help you and wdwerker have given me.  I will make a final decision tonight and get started tomorrow.  Thanks

Roland

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.