Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Oil versus Wax

Featured Replies

I'm in the process of finishing a island table for my cottage that I have fully constructed from salvaged 3x9 fir timbers.  For the base I used a wire brush to clean up the boards and that is working out fine as it has given a very rustic look.  However for the top I had to cut and plane all four sides of the boards to get a uniform, flat and of course clean surface.  The end product will be a butcher block style top that is about 3 1/2" thick (4x6 is size).  My problem is, what is the best product to finish the top with?  I've looked at Linseed Oil, Tung Oil, combinations of oil and wax but really can't find something that gives me 100% confidence.  The bare wood is very bright so I would ideally like to get some amber color back into in the wood that highlights the grain and hopefully has a soft (i.e. not polyurethane/glossy) finish.  Obviously it needs to have some protectant ability from water and stains as well.  Thanks so much for any advice/ideas you may have. WW

I used Rubio Monocoat on a walnut table base and liked it.  It is a mix of oil and wax with some sort of hardener to help the oil cure.  It leaves a very natural finish, no film whatsoever but seals the wood enough that you can wipe it down.   It is designed for floors so is more durable than tung oil or boiled linseed oil.  it is also easy to reapply when the finish becomes worn.  

http://www.hardwoodmall.com/product/rubio-2-part-small/

This thread contains pictures of my table, scroll toward the bottom to see it with the oil finish.

  

  • Author

Thanks for those suggestions.  I have never used General Arm-R-Seal.  Do you think this might be a solution as well?

 

14 minutes ago, Weekend Wood said:

Thanks for those suggestions.  I have never used General Arm-R-Seal.  Do you think this might be a solution as well?

 

I am a big fan of Arm R Seal.  Despite what the can says, it is a diluted varnish (it is basically 50% polyurethane / 50% mineral spirits).  2 or 3 thin coats will protect the wood without looking like a varnish.  More than 3 coats and you start to build a film, which will give you more protection but also give you a varnished look.  

For anything that might serve as a food prep surface, especially if it is end grain, I use a mineral oil / beeswax mixture. 100% edible, absorbs into the wood, easy to apply, and repels water quite well after a few coats. It is available commercially, or you can mix your own. I suggest about a 50/50 mixture, by weight, not volume. Use a double-boiler to melt the wax and mix with the oil.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.