Recommended Posts

Posted

Just received my new router bit. Locking Miter. I purchased a set up tool (Infinity) to use with it. I spent the weekend experimenting and trying to get two matching joints. I'm getting closer (running low on scrap pieces). My questions are two; Is the profile the same between manufacturers? And two, should I sneak up on the final cut so as not to take all the material out in one pass or will that get a cut that doesn't match it's mate?

Posted
30 minutes ago, Rex Edgar said:

Is the profile the same between manufacturers?

No, not necessarily. But the bottom of the middle cutter is centerline, that's why the jig has a wide throat. Whatever the centerline is off the table is the same setback for the fence. Jig or no jig, it's a PITA! Once you get it set right for your stock thickness, save both pieces and use them along with the jig for future set up. Chances are, you'll still need an adjustment. They have to be spot on or it won't work. Don't sneak up on the cut, you'll be chasing your tail all day doing that. You have to find the sweet spot and keep it !

Here is a pretty good video explaining the set up process. 

 

Posted

For me, this is one of those times I'd get an old cutting board or other similar chunk of thick plastic and cut it to be used in the future as set-up template.  It won't change shape with humidity like wood might. And you can easily trim it down for storing it with the bit.

Posted
40 minutes ago, collinb said:

For me, this is one of those times I'd get an old cutting board or other similar chunk of thick plastic and cut it to be used in the future as set-up template.  It won't change shape with humidity like wood might. And you can easily trim it down for storing it with the bit.

They sell set up blocks made out of high desity plastic for a whopping 10 bucks. Using wood isn't an issue as any significant  movement will be across the grain and this application uses the edge. If you've ever set up a lock miter bit you quickly realise no matter how good your jig is fine tuning will be necessary anyway. Point being...I don't care if the jig is precisely ground from a 5000 year old fossil.. you're gonna be playing with the fence and bit height again before it's right.

Posted
Just now, Janello said:

They sell set up blocks made out of high desity plastic for a whopping 10 bucks. Using wood isn't an issue as any significant  movement will be across the grain and this application uses the edge. If you've ever set up a lock miter bit you quickly realise no matter how good your jig is fine tuning will be necessary anyway. Point being...I don't care if the jig is precisely ground from a 5000 year old fossil.. you're gonna be playing with the fence and bit height again before it's right.

Ok. $10 isn't too bad.

I've not set up one of those but have had to re-set the door panels ogee bits.  Similar headache.

Anything involving a patter match is, in my mind, better than the rule/scale approach.

Posted

After another morning, experimenting, I'll probably stick with standard miters with a biscuit or spline joint. When I get two pieces to mate properly, the point of the miter (visible after assembly) doesn't have enough meat and I end up with a ragged looking joint.  Expensive experiment.... Another consideration was the router speed. According to a chart on the package, the larger the bit the slower the speed. Router is old Makita 2plus HP w/o speed adjustment. At 22,000 RPM I would hate for there to be a problem.

Posted
36 minutes ago, Rex Edgar said:

When I get two pieces to mate properly, the point of the miter (visible after assembly) doesn't have enough meat and I end up with a ragged looking joint.

Yup. You have to have perfectly square stock and leave that corner intact while not creating a ledge. Hence PITA!!! 

Mine collects dust as well.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 64 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined