sjm1580 Posted November 2, 2016 Report Posted November 2, 2016 Wondering if anyone has any experience with these systems. I will be using it in a small shop with maximum run of about 15 feet and wonder if this unit might cut it. Trying to find a quality unit and this Jet comes with a 5 year warranty. http://www.jettools.com/us/en/p/jcdc-2-cyclone-dust-collector-2hp-230v/717520 Thanks! Steve Quote
sjm1580 Posted November 13, 2016 Author Report Posted November 13, 2016 Alright folks I have volunteered to be the huckleberry for this one, and take the plunge on this Jet 2hp cyclone DC. I will give a review once I get it set up and in use. Steve Quote
mat60 Posted November 13, 2016 Report Posted November 13, 2016 Congrats on the cyclone. Be cool to hear how you like it Steve. Quote
Lt CHEG Posted November 13, 2016 Report Posted November 13, 2016 I've got that unit, and so far I like it well enough. I don't have a drum sander or anything too crazy and all I've been using it with is my table saw, jointer and planer and it seems to do a reasonable job. I've got two Rockler extendable length dust right flex hoses with blast gates that I use with the system and it works well enough for me. I think I'm similar in that my furthest run is probably a little under 15 feet. I've got no complaints thus far but if I do I'll be sure to report them. Good luck! Quote
Brendon_t Posted November 13, 2016 Report Posted November 13, 2016 Cool. look forward to hearing how it is. Lt. if you ever need more umf, get rid of those long flex runs. those things kill your flow. Quote
sjm1580 Posted November 13, 2016 Author Report Posted November 13, 2016 8 hours ago, Lt CHEG said: I've got that unit, and so far I like it well enough. I don't have a drum sander or anything too crazy and all I've been using it with is my table saw, jointer and planer and it seems to do a reasonable job. I've got two Rockler extendable length dust right flex hoses with blast gates that I use with the system and it works well enough for me. I think I'm similar in that my furthest run is probably a little under 15 feet. I've got no complaints thus far but if I do I'll be sure to report them. Good luck! Do you have the 2 hp unit? Quote
Lt CHEG Posted November 13, 2016 Report Posted November 13, 2016 2 hours ago, sjm1580 said: Do you have the 2 hp unit? Yes I do. I'm only just now having my shop insulated so my walls were open when I was buying equipment. It was super easy for me to run a dedicated 240 volt circuit for it. I've got my table saw and jointer on the same circuit as I won't be using both at the same time, but since I'll be using the dust collector with everything the dust collector is the only appliance on that circuit. 11 hours ago, Brendon_t said: Cool. look forward to hearing how it is. Lt. if you ever need more umf, get rid of those long flex runs. those things kill your flow. I eventually plan on running hard piping once my shop is a little more finished, and as the budget allows. I figure eventually I'll remove the two 4" line adapter and plumb hard pipe from the dust collector directly to a main overhead trunk line. I've got a pretty big shop space, but the initial budget didn't allow for a big shop space AND a well finished shop space so I'm making additions bit by bit. For starters my current setup didn't break the budget and worked passably so it was a starting point, but eventually I do plan on bigger non flex lines coupled with shorter flex runs. Once the insulation contractors are done and I have everything back where it belongs I'll try to post some pictures. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.