Recommended Posts

Posted

What do you want to do with it?

If you're turning small things, like pens, ducks calls, small bowls or boxes, and the like, then most small lathes will work fine for you. Something as small as a 6x18 upto 12x24 should be doable.

If you want to turn big bowls, then you need to get a lathe with longer swing over arm capacity.  Now you're talking in the 12 to 24 x 24-36 inch range.  Getting a lathe with a rotating headstock is desirable for really big bowls. 

If you want to very long spindles, like table legs or bannisters, then you don't need a large swing capacity, but length.  A 12x36 would work fine for this. 

The next question is, what is your budget?  If you are talking about the used CM or the HF, then we're assuming <$300.   Just beware, you may have the lathe, but there's a gazillion other do-hickeys you'll want with it.   So price those out to be included in your budget.   At the very least, A good beginners carbide tool or a set of HSS tools will run around $100 on their own.   There's also quite a few chucks and mandrels and other things you'll want for the lathe itself too.   A nice chuck with a couple jaws will run at least $200 new, and a lot of new lathes don't come with that.  That used CM might have a bunch of stuff with it already  though (link to the CL ad?).  

Generally speaking, the HF lathes have decent reviews.  There's not much to get wrong in a lathe, motor spins, drive shaft turns, ways and stocks are lined up.  If those are good, you have a decent lathe.  If they're not, it's almost useless.    Given the price and capacity of that CM lathe, and the pretty good chance there may be some tools and accessories tossed in, I think it's a good deal. 

But for the bottom line, if the lathe is in good working condition, it's tough to go wrong on a good deal.  You will learn if you enjoy turning or not, and know what you need to add from there.  Eventually you can cash this one in and upgrade if you choose. 

Other lathes to look at for comparison would include some of the smaller Nova's, Turncrafter by Penn State Industries, and quite a few others

  • Like 1
Posted

I have an old tube-bed Craftsman lathe. While mine seems OK, I've heard horror stories about these things, mostly that the tube gets twisted so the centers no longer align. Given a choice, I would pick a flat-bed lathe over the tube. If you can source the budget, electronic variable speed control is a really nice feature to have. But not a deal-breaker.

  • Like 2
Posted
3 minutes ago, wtnhighlander said:

. If you can source the budget, electronic variable speed control is a really nice feature to have. But not a deal-breaker.

Another thing I was going to mention, but forgot.  VS is a very nice feature to have, but can increase the price of a lathe enough to push it out of budget sometimes.  Depending on the motor you get, a VS retrofit might be possible.  But it might not be a good idea given the actual drive mechanism you get. 

Posted

A 12"x37" with HSS tools for $150?  I think that's an easy buy.  Assuming it run fine, it'll be hard to go wrong on this one.   This will definitely get your foot in the door for wood turning.   Even if the motor doesn't turn over, the belt layout will make it easy to add an aftermarket motor.  As long as the drive shaft spins, you'll definitely get some use out of it.    Even if you don't get that much into turning, this one will help you make table legs and such later, saving you money. 

It seems to have a spur center on the head stock and let's hope a live center on the tail stock (I can't see it not being a live center, else it wouldn't turn).  The drive shaft appears to be (might not, hard to tell in the pic) a threaded shaft and that's good.  When you go to purchase, ask what Taper the headstock is (on the inside).  I'm going to assume a Morse Taper 2, but it might be 1, or another taper altogether.  If it's a MT2, your golden, most lathe accessories that go into a taper are MT2 (for hobbyist use).  If it's a MT1, then your still ok, but your choices will be slightly limited.  If it's another taper (I doubt it is), do some research into the availability of parts.  Or if you know a machinist, you could have some adapters made.    Learning the thread size should be easy, and whatever it comes out to, you can always get an adapter (Nova has a good selection of them, or a friendly machinist can help).  I'd say there's a really good chance most commercially available chucks should work on this.  And if you're lucky enough, the tail stock will be tapered also, allowing you to easily use a jacobs chuck for drilling. 

The tools are marked as High Speed Steel, which is what you want.  You'll have to invest in a sharpening system, but you can build your own rig for fairly cheap with any slow speed grinder, or invest in a complete system.    There's a bunch of good tutorials on YT on how to sharpen.

When you go to look at it, dismount the blank in the machine, and slide the tailstock up to the headstock.  You want the tips of the two centers to touch point to point.   Given the price of the machine, if they're off by a hair so, it will be ok.   Back the tail stock off a bit, and then turn the machine on, make sure the machine runs and the drive shaft isn't grinding or anything else wonky.  If it runs fine, buy the sucker.

As it stands now, assuming you can get the tools sharp, you will easily be able to do spindles 'out of the box'.  For other stuff, you will have to buy a few accessories.  There is no mass to this lathe though, you're going to have to bolt it to a bench or stand, else it's going to dance around.   Those speeds are a bit scary though.  This is designed to be turning spindles, which usually tolerate higher turning speeds.  If you get into anything bigger or more unbalanced before truing, the turning is going to be scary.  You might want to invest in a variable speed adapter that the lathe plugs into.   875 is scary fast for a really rough bowl, especially for such a lightweight machine, and the 1hp means it has the oomph to get some heavier stuff spinning. 

I'd buy it if I was starting out again.   

  • Like 2
Posted
4 hours ago, Jeremy Carlsten said:

Someone snatched it up just before I called. Good info anyway, thanks again

 

Sent from my SM-G925V using Tapatalk

 

 

 

OWWM rule #5 In the time between finding a machine and asking others if you should buy it someone else will come to the proper conclusion.   

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   4 Members, 0 Anonymous, 54 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined