Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Red Oak Table

Featured Replies

I've been looking through the forum for the answer to my question, but can't seem to find it. I'm new to the forum and an amateur woodworker.

I'm looking to build a trestle table for my wife. We went to the lumber yard to pick out the wood type and she settled on red oak. I have never worked with red oak before so I have some concerns. I don't have a planer but my lumber yard can plane the wood for me. If they plane the wood and I bring it back to my garage workshop, if I stack and sticker the wood how long should I wait for the wood to acclimate to the environment before I can begin working? I live in Illinois and the weather right now is changing daily. What other issues can I expect from red oak?

 

Thanks!

If the material is kiln dried and it was stored somewhere with an environment similar to your own shop, you can begin working immediately.  In fact I would advise you to begin as soon as you can so it doesn't have time to move around too much before you do your joinery.

Keep your parts stickered and stacked throughout the entire process...at the very least at the end of each day.  I don't like my material laying flat on a surface ever...unless I'm working on a particular piece, it's always stickered.  Always.  Even air flow is the biggest card you can stack in your favor.

E, the last couple of days I've noticed a change and this last post confirmed it, no mention of red oak. Have you been receiving packages from Mel? 

  • Popular Post

LOL  Uh, no?

 

425.biglebowski.cm.41411.jpg

 

It does feel good to be able to post that pic ^^^...and not worry about losing my job. :D

 

 

Do you even sticker your lumber before milling Eric?  I've never even considered it...but I never really put much thought into stickering at all since I typically start working with the piece right after milling.

1 hour ago, bleedinblue said:

Do you even sticker your lumber before milling Eric?

No I don't.  All of my lumber is stored in stacks on the racks, no stickers.  My entire collection is comprised of kiln dried material, so it's perfectly acclimated to my shop's climate (or my shed, a similar environment, slightly more humid).  So there's not much need to sticker them since the first real change to them won't be made until I start milling.  At that point on, always stickered.

There are exceptions: If you're working with some big 16/4 legs like a I currently am with this bed, there's no need to sticker those (although I still usually do because my OCD won't allow it)...they're too thick to move in any significant way.  Also small parts...any part that's simply too small to move in any significant way.  But I err on the safe side and do sticker almost all parts because it takes about a nano-second to do it.

1 minute ago, Eric. said:

No I don't.  All of my lumber is stored in stacks on the racks, no stickers.  My entire collection is comprised of kiln dried material, so it's perfectly acclimated to my shop's climate (or my shed, a similar environment, slightly more humid).  So there's not much need to sticker them since the first real change to them won't be made until I start milling.  At that point on, always stickered.

There are exceptions: If you're working with some big 16/4 legs like a I currently am with this bed, there's no need to sticker those (although I still usually do because my OCD won't allow it)...they're too thick to move in any significant way.  Also small parts...any part that's simply too small to move in any significant way.  But I err on the safe side and do sticker almost all parts because it takes about a nano-second to do it.

Right on.  I can't remember not stickering causing any problems yet (at least not where I was able to point the finger at movement after milling), but it certainly makes sense as a "best practice" sort of thing that I should start incorporating.

It is indeed...best practice.

I should also add...if you were asking when in the case that I bring lumber home from the lumberyard and immediately start a project with it...yes, I will sticker it then before milling.  Not really so much because I think the lumberyard's environment is significantly different from my shop's (it's literally five minutes away and the yard is a semi-conditioned drywalled box just like my shop), but rather I already have to stack the damn boards somewhere anyway, so I might as well just throw some sticks between them while I do...so I do.  I seriously doubt that any significant change would be occurring either way.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.