Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Enclosing Cyclone Filters to reduce the noise

Featured Replies

I have spent quite a bit of time researching how to best reduce the Clearvue CV1800's noise level by not entirely enclosing the machine, but just the filter stack. I currently do not "believe" I have the space for a dust collector closet or for a large freestanding enclosure. I say "believe" because I could be persuaded to redesign my current enclosure and try it again, but I really would like to see all the dust/chips being pulled into the clear cyclone body. . . can you blame me that it looks cool? :rolleyes:

With all that said, I am not looking for a whisper quiet solution. I would like to reduce the awesome jet turbine noise the cyclone makes by 10-20 decibels (I understand this depends on the frequencies I want to dampen and the distance to the source. . . I have learned too much already about sound absorption).

So far here is the design I have borrowed from a gentleman which goes by VermontDale. He was an active contributor on the Clearvue forums (I have also posted there, however traffic is low), but unfortunately passed (RIP VermontDale). VermontDale's design is attached and other forum members said it worked amazingly well. He was trying to quiet the CV1800 so the community he was in could use it without bothering the other residents. 

I am going to replicate his design with the following modifications:

  • I will utilize an MDF (outside shell) - Green Glue - MDF - Roxul (inside) construction to dampen the exhaust sound. Thanks @drzaius for your suggestions on my shop build ramble.
  • The enclosure will be able to be "peeled" away with a hinged and latch configuration for easy cleaning of the filter stack. The ends will seal round the inlet of the filter stack and the fine dust clean out.
  • I will connect the enclosure to the blower housing with 4-8' of insulated duct to help further reduce the noise.

Here are a few of my questions:

  • How do I ensure there is enough air flow out of the enclosure to not hamper the performance? 
    • Do I utilize exhaust vents which disrupt the air flow? Create another chamber where the air pushes out after making a series of turns?
  • Do I need additional sound dampening on the enclosure since there is not an air gap?
  • Any other ideas/criticisms?

I have also attached where my cyclone is mounted in my garage. I would like to move the gun cabinet into the upstairs and place the enclosure for the filter stack there.

Thank you all for your help!

End View.jpg

Top View.jpg

92CB28DB-C0E2-4704-B1F4-5B84AC38217E.JPG

Maybe 10, which is half as loud. If you can make it a little bigger to lower pressure loss & then do a U-turn at the end it would be a lot quieter.

Hmm, the difference between 10 and 20 db is logarithmic and are actually a factor of 10 different. 20 db is ten times as loud and 10 db. 

Ten times the intensity. They don't even say energy. True it is perceived as doubled, but perception is scaled on the basis of your normal range of hearing. Most of the sounds we are designed to hear exist between 50 and 120. As this is my day job, I will say the perception is not what will help you deal in the construction of an enclosure. An understanding of intensity is what will make a difference. 

Regardless, covering the filter only is not going to do it. Building a whole closet around it lined with insulation maybe cuts it in half. Mine made a difference, never measured it though. 

You pretty quickly run into the point of diminishing returns with this. Half as loud would probably make it quieter than any of the machines. Mine's so quiet that I sometimes have to check the light to make sure it's on if a machine is already running. But my main concern was noise in the house, not in the shop.

  • 4 weeks later...

I see this is already 3+ weeks old so you may have already done what you planned to do. I doubt the noise is generated from the air flowing through the filter. The air exiting the HEPA filter on my new Oneida cyclone isn't sufficient to generate any significant noise. I enclosed an old Oneida cyclone on 3 sides with a plywood cabinet which I used to hold the collector in place. I even lined the 3 sides with carpet padding. I didn't sense any reduction in sound. The sound is generated by the motor and maybe the cyclone (not a sound engineer), so enclosing the whole collector in a separate enclosure would probably work, but you would need to be sure that the air being blown out the filter has a way out of the enclosure.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.